Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4

Results 1 to 3 of 3

Thread: Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4

  1. #1
    Registered
    Join Date
    Feb 2014
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4

    I recently was forced to upgrade my spindle which caused me to upgrade my Huanyang VFD(HY04D023B) to the Huanyang GT-5R5G-2. I am currently running Mach4 as my CNC controlling software.

    I currently have the new VFD (GT-5R5G-2)directly controlling the spindle 100% with no problems from the keypad on the VFD. I am running into issues with getting MACH4 to communicate with the new VFD. I can't get Mach4 to turn spindle on/off. Does someone have the settings in mach4 for this newer VFD drive? Possibly the wiring diagram for which terminals the on/off & Fwd/Rev should be hooked to?

    Currently not getting any indication from MACH4 that there is a fault. I believe there is a setting I maybe missing on the drive or one that I may have wrong.

    If anyone has any suggestions would be helpful.

    Thanks,



  2. #2
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    34410
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  3. #3
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    10015
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4

    Quote Originally Posted by Mikezl78 View Post
    I recently was forced to upgrade my spindle which caused me to upgrade my Huanyang VFD(HY04D023B) to the Huanyang GT-5R5G-2. I am currently running Mach4 as my CNC controlling software.

    I currently have the new VFD (GT-5R5G-2)directly controlling the spindle 100% with no problems from the keypad on the VFD. I am running into issues with getting MACH4 to communicate with the new VFD. I can't get Mach4 to turn spindle on/off. Does someone have the settings in mach4 for this newer VFD drive? Possibly the wiring diagram for which terminals the on/off & Fwd/Rev should be hooked to?

    Currently not getting any indication from MACH4 that there is a fault. I believe there is a setting I maybe missing on the drive or one that I may have wrong.

    If anyone has any suggestions would be helpful.

    Thanks,

    You can wire direct to S1 and com from you Breakout board outputs voltage range 9v to 30v you have to set the correct Parameter also for remote control, this can be also done with a Relay as well

    Modbus is good if you can set it up

    Mactec54


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4

Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4