Don't try to run it again until you have the proper settings, or you'll damage the spindle.
The seller doesn't have a manual?
Hello,
We bought a spindle motor and VFD from ebay - zero previous experience with such things.
https://www.ebay.co.uk/itm/112622600823#rwid
We completed the wiring, VFD and motor both work
Problem is that motors RPM is way too low and the VFD shows only max 60 HZ when running. The speed can be adjusted only between 0 and 60.
The manual is too confusing for us and we can not understand which factory settings need to be changed.
Only thing we could think of is to change most 400s to 300s with no luck.
Most similar manual to ours I could find online:
http://www.frequency-converter-china...2143083921.pdf
Any tips that could help us forward are greatly appreciated.
Many thanks ahead,
phootsman
Similar Threads:
- Need Help!- Installed spindle power quick change, now my spindle is dead, need motor resistance
- 3HP Servo Motor (potential use as spindle motor upgrade on an X3 or G0704) - No Longer Available
- Spindle motor set,1pcs 2.2kw spindle + inverter+ spindle mount bracket+ER collet
- Need Help!- Temperature on Spindle Motor (replacement with treadmill motor) on X2 or X3
- Which motor and drive for g0704 spindle motor control
Don't try to run it again until you have the proper settings, or you'll damage the spindle.
The seller doesn't have a manual?
Gerry
UCCNC 2017 Screenset
[URL]http://www.thecncwoodworker.com/2017.html[/URL]
Mach3 2010 Screenset
[URL]http://www.thecncwoodworker.com/2010.html[/URL]
JointCAM - CNC Dovetails & Box Joints
[URL]http://www.g-forcecnc.com/jointcam.html[/URL]
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Some advice for buyers, when you see advertised imported German Bearings, don't buy from this seller, the German Bearing they use a manufactured in China
Always Buy a VFD with a common Brand name not some look alike, like this one is this looks like the popular Huangang VFD Drive, don't be fooled by look a likes or copies
Here is a rough list of what Parameters you need to set
P00.00=300
P00.04=300
P00.05=300
P00.06=100
P00.09=200 ( adjustable for you Spindle Minimum Speed, Keep it safe nothing below 100 )
P01.04=100
P0.600=10
P0.700=300
P12.00=12
P12.01=220
P12.02=2
P12.05= ?? ( Your VFD Drive Max Amps Output )
Mactec54
P00.09 - factory settings were 0,2. Set it to 200, the motor stopped working
P0.006 - did you mean 00.06? 00.06 can only be set between 0 and 1
Went over the manual again and changed P07.08 (Frequency source selection 1). Finally got the speed needed.
Problem now is that the speed adjustment knob does not do anything.
Last edited by mactec54; 04-07-2018 at 11:22 AM. Reason: chaned P03.09=300
Mactec54
Sorry. I meant 06.00. You wrote "P0.600=10" and I assume you meant 06.00 , Acceleration Time. This can only be set 0-1
The ones below should be aleady set as you suggest because they are factory defaults.. Can't check the machine now but per manual those are defaults
P00.01=0
P03.08=0
P03.09=400
It should of been P06.01=2 not P06.00 my mistake
P06.01=2 Default is 2 you may need this higher for these Spindles this is the acceleration time
P06.02=2 Default is 2 also this may need to be higher, this is Deceleration Time
P03.08=0
P03.09=300 This to is not the Default and needs to be set also, this is for the maximum Spindle speed
P03.09 I posted this as 400 but that is incorrect for your Spindle
Mactec54