PIC Open source Servo Driver Schematics development? - Page 5

Page 5 of 5 FirstFirst ... 2345
Results 81 to 91 of 91

Thread: PIC Open source Servo Driver Schematics development?

  1. #81
    Member
    Join Date
    Apr 2006
    Location
    TURKEY
    Posts
    54
    Downloads
    0
    Uploads
    0

    Default Linistepper Lini8 New PCB

    In linistepper-lini8 power transistor mounted between pcb and heathsink
    Regards
    Argun

    Attached Files Attached Files


  2. #82
    Registered
    Join Date
    Oct 2005
    Location
    Lithuania
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    Hi Argun,
    Some components are mising in your component list (IC4, IC5, R11A, R12A, R46, R50-R52). Can you post full component list? Also I found discrepancy between schematic and pcb. In schematic resistor R51 attached to pin 4 of IC5, on pcb to pin 3. Can you check which is right?
    Regards,
    Romas



  3. #83
    Member
    Join Date
    Apr 2006
    Location
    TURKEY
    Posts
    54
    Downloads
    0
    Uploads
    0

    Default components for lini8

    ***************
    Hi Argun,
    Some components are mising in your component list (IC4, IC5, R11A, R12A, R46, R50-R52). Can you post full component list? Also I found discrepancy between schematic and pcb. In schematic resistor R51 attached to pin 4 of IC5, on pcb to pin 3. Can you check which is right?
    Regards,
    Romas
    ***************
    Hi Romas,
    Sorry,
    Component list attched.
    R51 an IC5's photo diode are in series, there is no difference R51 position. The differences may occur during PCB drawing.
    Regards
    Argun

    Attached Files Attached Files


  4. #84
    Registered
    Join Date
    Mar 2009
    Location
    Greece
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    Hi to community (this is my first message here)

    tachus42 > I' m interesting for your project, but I like to have info about LCD displsy that you use.
    Can you propose a good type for this driver?

    thanks in advance



    excuse me for my English, I'm Greek



  5. #85
    Registered
    Join Date
    Jul 2009
    Location
    uaz
    Posts
    1
    Downloads
    0
    Uploads
    0

    Thumbs up thanks





  6. #86
    Registered
    Join Date
    Aug 2009
    Location
    Vietnam
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    Tôi mới bước đầu tìm hiểu về máy cnc, xin các đàn anh chỉ giáo



  7. #87
    Registered
    Join Date
    Jul 2005
    Location
    Italy
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    Hi,

    just redrawn schematic and PCB on Eagle.

    I added 5v from motor supply, and the layout is made for rack mount.

    Naturally TIP112 must be mounted behind PCB on alu plate.

    I hope can be useful

    Attached Files Attached Files


  8. #88
    Member
    Join Date
    Apr 2004
    Location
    United States
    Posts
    209
    Downloads
    2
    Uploads
    0

    Default

    So is this a servo driver or a stepping motor driver? granted I have not gone threw all of the posted pages but still I'm wondering? Last I knew lini stepper was an opensource stepping motor driver



  9. #89
    Registered James Newton's Avatar
    Join Date
    May 2005
    Location
    USA
    Posts
    1397
    Downloads
    0
    Uploads
    0

    Default

    berin, you are absolutely correct. The Linistepper is a stepper driver, not a servo driver. This thread apparently took a turn... LOL.



  10. #90
    Member
    Join Date
    Sep 2011
    Location
    West Bank & Gaza Strip
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default

    Hi,
    Lini8 charge-pump modification appears to work only for Linistepper Version 1, with Enabled is High. In Linistepper Version 2, however, Enabled is active low. Any suggestions on how to make Lini8 modifications work with Linistepper Version 2? Best regards.



  11. #91
    Member
    Join Date
    Sep 2011
    Location
    West Bank & Gaza Strip
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by agelkom View Post
    ***************
    Hi Argun,
    Some components are mising in your component list (IC4, IC5, R11A, R12A, R46, R50-R52). Can you post full component list? Also I found discrepancy between schematic and pcb. In schematic resistor R51 attached to pin 4 of IC5, on pcb to pin 3. Can you check which is right?
    Regards,
    Romas
    ***************
    Hi Romas,
    Sorry,
    Component list attched.
    R51 an IC5's photo diode are in series, there is no difference R51 position. The differences may occur during PCB drawing.
    Regards
    Argun
    Hi,
    Lini8 charge-pump modification appears to work only for Linistepper Version 1, with Enabled is High. In Linistepper Version 2, however, Enabled is active low. Any suggestions on how to make Lini8 modifications work with Linistepper Version 2? Best regards.



Page 5 of 5 FirstFirst ... 2345

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

PIC Open source Servo Driver Schematics development?

PIC Open source Servo Driver Schematics development?