Okuma


Page 1 of 142 12341151101 ... LastLast
Threads 1 to 20 of 2826

Forum: Okuma

Discuss Okuma machines here.

  1. Need Help!- Problems when sending .min files back to osp5000 control - it misses random chars.

    Started by nikolaiownz‎, 03-12-2019 03:34 AM
    2 Pages
    1 2
    • Replies: 17
    • Views: 273
    Today, 07:57 AM Go to last post
  2. Exclamation LU300 Tool Offset Page

    Started by alivexx1‎, 03-08-2019 12:40 PM
    • Replies: 7
    • Views: 211
    Today, 03:53 AM Go to last post
  3. trochoïdale milling on IGF?

    Started by duivenhok‎, 03-13-2019 02:41 PM
    • Replies: 4
    • Views: 166
    03-17-2019, 03:56 PM Go to last post
  4. 948 alarm help

    Started by pants‎, 01-28-2014 10:17 AM
    • Replies: 1
    • Views: 727
    03-16-2019, 02:40 PM Go to last post
  5. MX-45VAE DNC B set-up

    Started by Gemp‎, 03-12-2019 10:00 PM
    bits, dnc, mx-45vae, rate, stop
    • Replies: 1
    • Views: 105
    03-13-2019, 03:23 AM Go to last post
  6. Need Help!- Okuma Howa Act4

    Started by peterlwoods‎, 11-19-2016 10:26 AM
    batteries, customers, howa, load, okuma
    • Replies: 1
    • Views: 277
    03-11-2019, 06:37 PM Go to last post
  7. MX-45VAE operator's panel/keypad disassembly

    Started by jjjearls‎, 03-11-2019 11:18 AM
    bezel, hard, keypads, operators, press
    • Replies: 0
    • Views: 73
    03-11-2019, 11:18 AM Go to last post
  8. Barfeeder

    Started by gunda‎, 03-06-2019 02:12 PM
    bar, barfeeder, change, collet, profiled
    • Replies: 3
    • Views: 136
    03-08-2019, 05:09 PM Go to last post
  9. how to set up origins from code ?

    Started by deadlykitten‎, 01-27-2016 02:00 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 702
    03-08-2019, 09:47 AM Go to last post
    • Replies: 5
    • Views: 173
    03-07-2019, 06:08 PM Go to last post
  10. please, how to achieve oriented M axis ?

    Started by deadlykitten‎, 03-06-2019 06:16 AM
    • Replies: 1
    • Views: 120
    03-06-2019, 05:46 PM Go to last post
  11. Need Help!- LT15 lower turret hold

    Started by kurmay‎, 02-28-2019 04:06 AM
    axis, hold, lower, movement, turret
    • Replies: 7
    • Views: 168
    03-06-2019, 01:06 PM Go to last post
  12. altering work offsets from within a program (G92)

    Started by jay_dizzle‎, 03-05-2019 04:16 PM
    g92, mdi, program, solution, work
    • Replies: 2
    • Views: 137
    03-06-2019, 11:03 AM Go to last post
  13. okuma 5000 troubel

    Started by saifou‎, 03-01-2019 05:32 PM
    crt, image, panel, rom, share
    • Replies: 0
    • Views: 164
    03-01-2019, 05:32 PM Go to last post
  14. Problem- re-starting in the middle of a program?

    Started by jay_dizzle‎, 02-28-2019 03:40 PM
    • Replies: 5
    • Views: 177
    03-01-2019, 02:07 PM Go to last post
  15. Post Processor

    Started by machinebob1‎, 02-27-2019 09:22 AM
    myw, post, processor, program, spits
    • Replies: 3
    • Views: 326
    02-28-2019, 12:35 PM Go to last post
  16. Counter

    Started by machinebob1‎, 02-22-2019 04:16 PM
    alarm, back, bob, counter, power
    • Replies: 4
    • Views: 214
    02-25-2019, 09:11 AM Go to last post
  17. Fixing center height on Multus U4000

    Started by Dandyyo‎, 02-22-2019 07:33 PM
    • Replies: 1
    • Views: 139
    02-23-2019, 04:25 AM Go to last post
  18. Axis acceleration control

    Started by graemeian‎, 02-20-2019 09:52 PM
    abrupt, acceleration, commands, run, software
    • Replies: 1
    • Views: 137
    02-22-2019, 06:00 AM Go to last post

Page 1 of 142 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 76 users browsing this forum. (3 members & 73 guests)

  1. deadlykitten,
  2. mkricka,
  3. Roblid

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands