Need Help! MX45VAE Will not move after startup


Results 1 to 10 of 10

Thread: MX45VAE Will not move after startup

  1. #1
    Member Fireater's Avatar
    Join Date
    Feb 2021
    Posts
    38
    Downloads
    0
    Uploads
    0

    Default MX45VAE Will not move after startup

    Turned on machine ran through its checks all looks fine, press power on the control control fires up hydraulics same, but machine will not move. Hydraulics at pressure and oil, chiller the same, air same, no alarms. Cant run spindle or move table.. WTF something I'm missing??? Last time I ran it I pulled out the tool but I tried with it in and out.. Something I missed on startup?? any data needs to be entered?? buttons pressed??

    Similar Threads:


  2. #2
    Member OkumaWiz's Avatar
    Join Date
    Apr 2009
    Location
    United States
    Posts
    1262
    Downloads
    0
    Uploads
    0

    Default Re: MX45VAE Will not move after startup

    Is machine lock on? Axis inhibits on?

    Experience is what you get just after you needed it.


  3. #3
    Flies Fast Superman's Avatar
    Join Date
    Dec 2008
    Location
    Antarctica
    Posts
    3110
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by OkumaWiz View Post
    Is machine lock on? Axis inhibits on?
    Toolchange in mid cycle (not at start or tool staged position )
    rapid/feed rate override set to zero
    Residual move not yet complete (not after restarting)



  4. #4
    Member deadlykitten's Avatar
    Join Date
    Jun 2015
    Location
    Antarctica
    Posts
    4131
    Downloads
    0
    Uploads
    0

    Default Re: MX45VAE Will not move after startup

    Last time I ran it I pulled out the tool but I tried with it in and out
    hy, sometimes the claws that grab the pullstud may remain too long in an intermediate position, because of a wrong toolchange sequence; this may be caused by missalingment, because of manual toolchange, or because of swing arm - atc - spindle alingmnent

    as a consequnce, the hydraulic will be up for for too long, over a preset timer, that will jump a fuse in the electrical cabinet

    if you can not clamp/unclamp tools, then look for this; besides this check, i have no other idea / kindly

    we are merely at the start of " Internet of Things / Industrial Revolution 4.0 " era : a mix of AI, plastics, human estrangement, powerful non-state actors ...


  5. #5
    Member Algirdas's Avatar
    Join Date
    Mar 2009
    Location
    United Arab Emirates
    Posts
    1982
    Downloads
    2
    Uploads
    0

    Default Re: MX45VAE Will not move after startup

    if the pannel is not locked try select the MDI mode and command, for instance S500M3. OSP should show some alarm message.



  6. #6
    Member Fireater's Avatar
    Join Date
    Feb 2021
    Posts
    38
    Downloads
    0
    Uploads
    0

    Default Re: MX45VAE Will not move after startup

    No not that I know of.



  7. #7
    Member OkumaWiz's Avatar
    Join Date
    Apr 2009
    Location
    United States
    Posts
    1262
    Downloads
    0
    Uploads
    0

    Default Re: MX45VAE Will not move after startup

    Quote Originally Posted by Fireater View Post
    No not that I know of.

    I think all if what is suggested is good to try...what have you checked so far?

    Also please reveal what sequence your tool changer is on. (Look in the ATC display page) It should be at sequence 1. If not, you will need to get it there like superman says. Also try Al's test and let us know the result.

    Best regards,

    Experience is what you get just after you needed it.


  8. #8
    Member Fireater's Avatar
    Join Date
    Feb 2021
    Posts
    38
    Downloads
    0
    Uploads
    0

    Default Re: MX45VAE Will not move after startup

    Not locked not that I know of. Panel responds as it should. no fuses I can see popped. I put in a tool change in MDI and you can hear it want to respond but no hydraulic movement. tool will grab if I put one in manually. I can move the tool changer arm through ATC cycles with the cycle buttons on controller so it moves. No alarms shown.... WTF.... any ideas?? procedure list or possible corrective options lists would be helpful to eliminate possibilities. Start up procedure.. Power on, control on, open/close door, Should be ready.. MDI T6M06 just sits there, cycle start just sits there, I can not move the head/table to move or get the spindle to run.



  9. #9
    Member OkumaWiz's Avatar
    Join Date
    Apr 2009
    Location
    United States
    Posts
    1262
    Downloads
    0
    Uploads
    0

    Default Re: MX45VAE Will not move after startup

    If you let the control sit on the T6M6 and wait 3 minutes, what alarm pops up? Are the run, STM, lights on? If you go to block data and check the page are any of the codes blinking ON/OFF? Is the spindle orientation complete? When you try the MDI commands, what sequence # in the ATC page does it get stuck on? Is the door closed?

    BTW, I'm assuming it's a 5020M-G control, is this correct? Do you have the maintenance manual? If yes, the sequence for the tool changer is shown in there for your machine. Are you able to manually run it all the way through a tool change and back to sequence 1?

    Don't mean to shotgun you with questions, but rather give you clues to follow for troubleshooting.

    Best regards,

    Experience is what you get just after you needed it.


  10. #10
    Member Fireater's Avatar
    Join Date
    Feb 2021
    Posts
    38
    Downloads
    0
    Uploads
    0

    Default Re: MX45VAE Will not move after startup

    Thanks for the info. I have a OSP7000M control if that helps..



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

MX45VAE Will not move after startup

MX45VAE Will not move after startup