pls, is it possible to use g22 for c axis ?


Results 1 to 6 of 6

Thread: pls, is it possible to use g22 for c axis ?

  1. #1
    Member deadlykitten's Avatar
    Join Date
    Jun 2015
    Location
    Antarctica
    Posts
    3549
    Downloads
    0
    Uploads
    0

    Default pls, is it possible to use g22 for c axis ?

    - parameter's value doesn't matter, what matters is consistency
    - you can reduce cycle time not by reducing it, but by reducing it's uncertainty


  2. #2
    Member deadlykitten's Avatar
    Join Date
    Jun 2015
    Location
    Antarctica
    Posts
    3549
    Downloads
    0
    Uploads
    0

    Default Re: pls, is it possible to use g22 for c axis ?

    hy mr wizard no, it didn't work

    Code:
        G29 PC=30 ( 2277-01 ALARM-B DATA WORD torque limit A side 1 )
        G22 PC=25 C+10 F+60(100*5) G94 D+12.5 ( L0 still going )
        G28
    upper torque limit is at 60%

    but look what i found inside error's description ( is like there is possible to use PC and PM ) :

    Code:
    7 ->When it was not C axis connection, PC instruction was done by G22/G23/G29.
    8 ->When it was not M-axis specification, PM instruction was done by G22/G23/G29.
    9 ->PW and WT instructions were designated at the same time by G22.

    i may be missing something, because it did not showed " no-spec alarm " / kindly

    ps : please, what means WT from point 9 ?

    - parameter's value doesn't matter, what matters is consistency
    - you can reduce cycle time not by reducing it, but by reducing it's uncertainty


  3. #3
    Member deadlykitten's Avatar
    Join Date
    Jun 2015
    Location
    Antarctica
    Posts
    3549
    Downloads
    0
    Uploads
    0

    Default Re: pls, is it possible to use g22 for c axis ?

    if you wish, please check attached seems that such an option was released recently

    Attached Thumbnails Attached Thumbnails pls, is it possible to use g22 for c axis ?-untitled-png  
    - parameter's value doesn't matter, what matters is consistency
    - you can reduce cycle time not by reducing it, but by reducing it's uncertainty


  4. #4
    Member OkumaWiz's Avatar
    Join Date
    Apr 2009
    Location
    United States
    Posts
    1170
    Downloads
    0
    Uploads
    0

    Default Re: pls, is it possible to use g22 for c axis ?

    Now that’s a new one! Never seen it before.

    I’m guessing there is a new torque limit parameter for c axis then?

    Best regards,

    Experience is what you get just after you needed it.


  5. #5
    Member deadlykitten's Avatar
    Join Date
    Jun 2015
    Location
    Antarctica
    Posts
    3549
    Downloads
    0
    Uploads
    0

    Default Re: pls, is it possible to use g22 for c axis ?

    hy, i think that this capability is there from some time, as PC appears inside manuals, in G22 context; it may be spec, but it hadn't been presented so far

    from time to time, i scroll the okuma website, and recently i saw it

    i think that torque limiter parameter is the same as the existing one, as it is targeting only the upper limit, beyond which is not allowed to pass when using G29



    a few months ago, when i needed this, i simply used spindle's phase ( CD on screen ), and a live tool that was aligned among X axis, but offseted in Y; normally, Y offset should have been 0, but sometimes is possible to go like that now, looking back at it, i think i could have ignored also the X alingment

    is possible to have same origin for C axis and M19, so to switch between them without losing phase / kindly

    - parameter's value doesn't matter, what matters is consistency
    - you can reduce cycle time not by reducing it, but by reducing it's uncertainty


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

pls, is it possible to use g22 for c axis ?

pls, is it possible to use g22 for c axis ?

pls, is it possible to use g22 for c axis ?