Need Help! Problems when sending .min files back to osp5000 control - it misses random chars. - Page 2


Page 2 of 2 FirstFirst 12
Results 13 to 21 of 21

Thread: Problems when sending .min files back to osp5000 control - it misses random chars.

  1. #13
    Member
    Join Date
    Feb 2009
    Location
    usa
    Posts
    5935
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    No, it's with parity stop bits, etc. 7 or 8 is the two options.

    Sent from my SM-T813 using Tapatalk



  2. #14
    Member
    Join Date
    Jan 2010
    Location
    Denmark
    Posts
    83
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    Okay there might be something into that.

    Deadly kitten says that there is something every 256 char op on the post.

    I use hardware on the pc if I don't it's not receiving anything at all.

    Sendt fra min EML-L29 med Tapatalk



  3. #15
    Member deadlykitten's Avatar
    Join Date
    Jun 2015
    Location
    Antarctica
    Posts
    2549
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    hy nikolaiownz, i really have no clue about cimco, but please look into those 7&8 bits like underthetire said, and also look over xon/xoff like mr Wizard said ... those guys know what they are saying

    i am not sure, but maybe you can use a floppy emulator ? please check this out :


    Quote Originally Posted by OkumaWiz View Post
    some people are replacing the floppy drives with Floppy to USB conversions. They have USB ports and they show up as multiple FD drives of 1.4Mb each so then it becomes possible to run more than even 1 floppy can hold. I think as much as 99 floppy drives can be accessed from 1 usb. You can find them on ebay for about 10 times less than you can get them from your dealer
    it is from post 14 from here : https://www.cnczone.com/forums/okuma...are-posts.html

    kindly

    Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg


  4. #16
    Member
    Join Date
    Jan 2010
    Location
    Denmark
    Posts
    83
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    Quote Originally Posted by deadlykitten View Post
    hy nikolaiownz, i really have no clue about cimco, but please look into those 7&8 bits like underthetire said, and also look over xon/xoff like mr Wizard said ... those guys know what they are saying

    i am not sure, but maybe you can use a floppy emulator ? please check this out :




    it is from post 14 from here : https://www.cnczone.com/forums/okuma...are-posts.html

    kindly
    I Will be looking into it tomorrow when I get to the shop. Thanks

    What do I look for in xon/xoff ? I a fairly new to dnc setups so sorry for asking ø

    Sendt fra min EML-L29 med Tapatalk



  5. #17
    Member
    Join Date
    Feb 2009
    Location
    usa
    Posts
    5935
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    Quote Originally Posted by deadlykitten View Post
    hy nikolaiownz, i really have no clue about cimco, but please look into those 7&8 bits like underthetire said, and also look over xon/xoff like mr Wizard said ... those guys know what they are saying

    i am not sure, but maybe you can use a floppy emulator ? please check this out :




    it is from post 14 from here : https://www.cnczone.com/forums/okuma...are-posts.html

    kindly
    No floppy to emulate on a 5000 early 5000 were still tape to load osp software and a little later they were huge 8" floppies.

    Sent from my SM-T813 using Tapatalk



  6. #18
    Member
    Join Date
    Jan 2010
    Location
    Denmark
    Posts
    83
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    Quote Originally Posted by underthetire View Post
    No floppy to emulate on a 5000 early 5000 were still tape to load osp software and a little later they were huge 8" floppies.

    Sent from my SM-T813 using Tapatalk
    Yup mine has tape and huge floppy disk

    Sendt fra min EML-L29 med Tapatalk



  7. #19
    Member oldjudge's Avatar
    Join Date
    Jan 2012
    Location
    United States
    Posts
    12
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    Have you tried adjusting the baud rate? I've seen where some of the 5000 controls will pick up wierd glitches at certain baud rates. Bumping the rate up or down a bit might clear this up.



  8. #20
    Member
    Join Date
    Jan 2010
    Location
    Denmark
    Posts
    83
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    Quote Originally Posted by oldjudge View Post
    Have you tried adjusting the baud rate? I've seen where some of the 5000 controls will pick up wierd glitches at certain baud rates. Bumping the rate up or down a bit might clear this up.
    Like I sayd I tried but it not sending at all with any other rates. Just get an error

    Sendt fra min EML-L29 med Tapatalk



  9. #21
    Member
    Join Date
    Jan 2010
    Location
    Denmark
    Posts
    83
    Downloads
    0
    Uploads
    0

    Default Re: Problems when sending .min files back to osp5000 control - it misses random chars

    Ok so i found the problem - it was a handshake problem.. the control was set to use hardware handshake. i changed parameters to what some guy wrote on the forums. now i use software on control and cimco and now it works like a charm.



Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Problems when sending .min files back to osp5000 control - it misses random chars.

Problems when sending .min files back to osp5000 control - it misses random chars.