Replace M30 to M02 and try again
This is last version of OSP to PC emulator.
FEATURES:
-You can drag and drop files between OSP formatted floppy and PC (BB1 directory)
-Initialize a floppy OSP Format
-Backup and restore OSP formatted floppies.
-Print file
-Delete file
-Protect or unprotect file
-Compare files
-View file on floppy
-View and edit file on PC
-Rename file
-View properties of files
etc..
LİNK:
okuma_osp_reader.zip download for free on file share letitbit.net
Similar Threads:
Replace M30 to M02 and try again
What is machine's name and which control unit?
You need to read-up on how to create your own thread on CNCzone, not hijack a topic that has no relation to your problem ( it has nothing to do with an OSP reader or RS232 settings )
Millac 6 VA......................this is a mill
Control OSP5020L..........this is a lathe specification.....read the manuals......possible screen was replaced from a lathe.....I'd guess to is an OSP5000-MG or a Fanuc control
correct procedure to selecting a program on OSP control
AUTO mode
- Program Select [F1] ...... > PS is on the lower command line
- ABC(.min) <WRITE>
the .min is a default setting and is not required to be typed. The program is parsed ( checked) that it meets certain requirements ie ends with an M2 or M30
the program should then be shown as the current run program, or an alarm is displayed for if it was not selected
To run that program, cycle start is then pressed
Errors in programming usually show as an alarm, It gives a number with a seriousness rating ( A means very bad, D means you can still run the machine )
- also it gives a description of the error.........this entire line is required to be stated to us for any possible solution
A program not running can be any number of reasons
- no movement commanded
- feedrate &/or rapid over-ride knobs turned to zero
- Single block is ON
- unsupported G or M code
- startup condition not being met. ie Doors closed, Fanuc controls require ALL axes to be homed
What is the alarm you are getting ? ( the number & the full description )
M6 by itself will do nothing
it must be used to call-in a tool that is registered in the tool carousel ie T1 M6 , or be "pre-selected" beforehand
Code:T1 M6 ( calls in T1 ) T2 (pre-select T2) G0... ... M6 ( calls in T2) T3 (pre-select T3) G0.... .... M63 (de-select the pre-selected tool, find empty pot ) M6 (empty tool in spindle)
Try t1 or a different tool, then m6. And make sure the z axis is up at the limit.
sent from me
It the tool pot in the down position? You should have a manual tool change recovery buttons on the front of the panel.
sent from me
No, something doesn't jive. No external PLC on a 5020, and your showing a build date of 1989, 5020 didn't come out till the early 90s.
sent from me
what the diagnostic screen shows at the ATC sequence stop?
Is there any chance you can host this file somewhere else? I think this would be very useful for me, as we use a lot of OSP5020 controls here, but I keep getting virus warnings from the host you have now. If it would be possible, you could even send it as an email attachment.
there's no need to host anything elsewhere. the file should have just been posted here, like this.....
It never occurred to me that you could attach files to posts here. Thanks!
Edit: I just tried the software, and it does everything I could ask for. Now I can access my programs on my Win7 laptop. Thanks again!
I would very much like to transfer files from BB1 OSP format, but it says binary files not supported.
I am developing the program for myself after that. That's why I stopped the distribution.
https://www.facebook.com/okuma.tuning
Hello, I would like to get this software. Do you still have it? If so please contact me
I have been reading helpful information on this site for a long time, not sure if I have ever posted or asked questions here as I usually find what I am looking for. Huge Thank you to everyone on this site. I have an OSP-7000L control lathe that I need to change the batteries in and I have the battery change utility on a floppy disk, however we changed out the floppy reader with a usb reader (emulator?) and I am trying to use your OSP reader program ver. 2.2.0.1 to transfer battery change utility from floppy disk to a thumb drive but am not having any success. Is there instructions as to how to use this program or maybe if there is an English version that I might understand? any help will be greatly appreciated!
Could you please share the okuma osp reader file again?