OKK

Page 1 of 8 1234 ... LastLast
Threads 1 to 20 of 141

Forum: OKK

Discuss OKK machines here.

  1. Need control service for OKK-MCH550/Meldas 5000

    Started by grweldon‎, 11-28-2007 11:55 AM
    not
    • Replies: 15
    • Views: 6,750
    10-02-2008, 08:10 PM Go to last post
  2. Need Help!- OKK Milcon III with MELDAS 83A

    Started by parametric.ms‎, 06-20-2008 12:31 PM
    far
    • Replies: 15
    • Views: 9,748
    08-21-2017, 01:55 AM Go to last post
  3. Connection & Download with DNC from PC

    Started by obieron‎, 02-29-2008 04:29 PM
    load parameters
    • Replies: 13
    • Views: 5,052
    12-08-2009, 10:49 AM Go to last post
  4. Need Help!- changing Spindle Bearings, how?

    Started by ThomasS‎, 01-06-2011 03:27 PM
    • Replies: 11
    • Views: 2,273
    02-03-2011, 08:10 PM Go to last post
  5. Need Help!- older than time okk

    Started by krow‎, 02-19-2009 05:22 PM
    • Replies: 10
    • Views: 3,002
    10-01-2009, 03:10 PM Go to last post
  6. Problem- machine won't start up

    Started by krow‎, 02-24-2009 08:41 PM
    away, goes, not, then
    • Replies: 9
    • Views: 2,788
    08-25-2009, 06:04 PM Go to last post
  7. Need Help!- UNKNOWN FAULT CODE

    Started by CNC_BOB‎, 08-29-2009 07:33 AM
    down, far, next, not
    • Replies: 8
    • Views: 10,857
    11-18-2022, 01:57 PM Go to last post
  8. Exclamation Need Help!- OKK MCV 500 machine manuals

    Started by venntec‎, 07-16-2010 08:01 AM
    • Replies: 8
    • Views: 5,691
    01-27-2011, 02:00 PM Go to last post
  9. Smile Need Help!- OKK Pallet Check M-Codes

    Started by CNC Kid‎, 05-20-2009 02:49 PM
    • Replies: 6
    • Views: 7,536
    11-01-2016, 09:25 PM Go to last post
  10. Question Need Help!- OKK Tech in Ohio??

    Started by JoBwan‎, 01-28-2008 06:41 AM
    not, retire
    • Replies: 5
    • Views: 3,118
    03-12-2010, 05:48 PM Go to last post
  11. Need Help!- RAPID OVERRIDE

    Started by CNC_BOB‎, 05-28-2008 09:31 AM
    • Replies: 5
    • Views: 2,980
    06-02-2008, 06:34 AM Go to last post
  12. Question Need Help!- ATC HELP

    Started by TANGENT1‎, 03-30-2010 08:08 AM
    • Replies: 5
    • Views: 2,452
    05-06-2011, 02:44 PM Go to last post
  13. Need Help!- emg ls problem MCV 460

    Started by Elmss12‎, 05-16-2008 01:36 PM
    down, then
    • Replies: 4
    • Views: 3,729
    06-20-2016, 09:48 PM Go to last post
  14. Need Help!- SPINDLE WARMUP

    Started by CNC_BOB‎, 04-09-2009 08:04 AM
    plus
    • Replies: 4
    • Views: 3,584
    05-01-2009, 04:32 PM Go to last post
  15. Need Help!- OPERATOR MESSAGE NO.2006

    Started by KHOATRANNGOC‎, 09-29-2011 12:12 AM
    not, operator message
    • Replies: 4
    • Views: 3,531
    11-16-2011, 08:34 PM Go to last post
  16. Fanuc10M Parameter

    Started by Jones'r‎, 10-19-2012 06:13 AM
    • Replies: 4
    • Views: 1,342
    10-23-2012, 10:17 AM Go to last post
  17. How do I rigid tap on a VM 7 III

    Started by Mazakdude‎, 04-16-2008 11:15 PM
    • Replies: 3
    • Views: 2,727
    05-20-2008, 05:16 PM Go to last post
  18. Need Help!- 1015 Mag Amp Troubled

    Started by cncman007‎, 07-02-2012 05:26 PM
    • Replies: 3
    • Views: 1,396
    07-23-2012, 05:15 PM Go to last post
  19. OKK HM500S FANUC 300is Series Axis' wont zero

    Started by AZTEXAN_MIMXII‎, 12-11-2012 05:48 PM
    • Replies: 3
    • Views: 2,213
    12-28-2012, 10:35 PM Go to last post
  20. Question Need Help!- Need help Toolchanger Macro Program

    Started by abergie‎, 03-14-2013 07:47 AM
    • Replies: 3
    • Views: 2,042
    05-23-2013, 05:05 PM Go to last post

Page 1 of 8 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands