Need Help! OKK Milcon III with MELDAS 83A - Page 2

Page 2 of 2 FirstFirst 12
Results 13 to 16 of 16

Thread: OKK Milcon III with MELDAS 83A

  1. #13
    Registered
    Join Date
    Apr 2008
    Location
    Indonesia
    Posts
    136
    Downloads
    0
    Uploads
    0

    Default

    Thanks a lot for replying my message.
    But I still don't get it how to make a rewind program in okk

    My control contain with this :
    1. Circular Interpolation
    2. Radius Programming on Arc
    3. Simultanous 3 Axis Linear Interpolation
    4. Return to Zero
    5. High Speed Return to Zero
    6. Mechanical Handle
    7. Rapid Traverse Override
    8. Stroke Check
    9. Additional Tool Offset 32 Set
    10. Cutter Radius Offset
    11. Canned Cycle
    12. Memory Type Pitch Error Compensation
    13. Auto Restart
    14. Decimal Point Program
    15. Program Number Search
    16. Tape Store 10m Edit
    17. Sub Program Function
    18. External Operation Board
    19. Built in Sequencer
    20. Built in Machine Operation Panel
    21. Xxxxx (kanji fonts)
    22. Tape Punch / Print Out I/F

    I have no idea how to activate the option parameter. Should I try one by one with hexadecimal configuration?
    How about yours? Is it same optional with mine?

    Sorry if I disturb you recently.

    Regards,
    Andre



  2. #14
    Registered
    Join Date
    May 2005
    Location
    VietNam
    Posts
    108
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by mosesooi View Post
    parametric.ms.
    Hi Andre,
    Okk Is A Good Machines But Not Meldas 83A!
    I Don't Think You Can Run M99 In Your Machine.
    All Limited M Code And G Code Is Stated In The Side Of The Main Panel.(Which Contains
    The Meldas 83A ).Please Keep In Mind, Your MC Is An NC Not CNC!!!
    Any How I Will Give You All The ParameterS You Need:

    S1 +0 +120
    0 120
    0 160
    0 0
    1 8000
    0 8000
    70 6000
    100 0

    CF +4000 +2
    4000 2
    4000 2
    0 0
    20 0
    20 0
    7 0
    0 0

    BR +4 +6400
    5 6400
    0 4800
    0 0
    0 0
    0 0
    0 0
    0 0

    T1 +5 +7
    5 3
    10 10
    3 30
    3 60
    3 5
    7 20
    7 7

    D1 +0 +2308
    0 2308
    0 2504
    0 0
    0 11
    0 10
    0 8
    0 0

    P1 -8901 -601
    8601 401
    8401 1011
    7601 3950
    6601 3850
    2601 3451
    1601 3051
    901 2251

    P17 -1951 -2251
    1851 1851
    1701 1450
    7511 650
    6511 250
    4251 +0
    3850 +0
    3451 +0

    FX1 +0 -921000
    0 -401000
    1000 -471000
    1000 +0
    300 0
    300 0
    300 0
    0 0

    Hi Mosesooi,
    Could you please PM me the 83A parameter setting procedure (and parameter list if possible)? My OKK have lost all parameter because battery was empty.
    Thanks a lot.



  3. #15
    Registered
    Join Date
    Jun 2017
    Location
    India
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: OKK Milcon III with MELDAS 83A

    I have two machine of OKK Millcon III (MHA 400 & MHA 300). Both has Meldas 83A controller

    The machine when bought was not in running condition and was idle for a while

    I tried to power up the machinery

    Both displays the same alarm E=20 when i try to power on the machine and release the emergency

    Moreover I tried to change the parameter which wasn't successful at all

    I have been told that it's a software related emergency parameter

    I'm not convinced with the reply

    I'm open to suggestions

    If needed I can send screenshots

    P.S. I have the original parameters. But i would like to know the parameter setting procedure. Because however we do it, we couldn't change the parameters other than the M list

    Kindly assist



  4. #16
    Registered
    Join Date
    Jun 2017
    Location
    India
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: meldas 83.....

    I have two machine of OKK Millcon III (MHA 400 & MHA 300). Both has Meldas 83A controller

    The machine when bought was not in running condition and was idle for a while

    I tried to power up the machinery

    Both displays the same alarm E=20 when i try to power on the machine and release the emergency

    Moreover I tried to change the parameter which wasn't successful at all

    I have been told that it's a software related emergency parameter

    I'm not convinced with the reply

    I'm open to suggestions

    If needed I can send screenshots

    P.S. I have the original parameters. But i would like to know the parameter setting procedure. Because however we do it, we couldn't change the parameters other than the M list

    Kindly assist



Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

OKK Milcon III with MELDAS 83A

OKK Milcon III with MELDAS 83A

OKK Milcon III with MELDAS 83A