Mechanical Calculations/Engineering Design


Page 1 of 103 12341151101 ... LastLast
Threads 1 to 20 of 2048

Forum: Mechanical Calculations/Engineering Design

Discuss general mechanical design and mechanical calculations.

  1. Sticky Threads
  2. Sticky Thread Sticky: PLEASE READ BEFORE POSTING IN THIS FORUM!

    Started by svenakela‎, 09-12-2007 03:00 AM
    its, regards
    • Replies: 0
    • Views: 12,362
    09-12-2007, 03:00 AM Go to last post
  3. Forum Threads
  1. Designing servo driven bt30 setup

    Started by QuinnSjoblom‎, 08-04-2020 11:47 AM
    3 Pages
    1 2 3
    • Replies: 42
    • Views: 2,041
    01-18-2021, 11:30 AM Go to last post
  2. Question Pulley/Socket Size Calculations Needed

    Started by jlbenn01‎, 01-11-2021 01:35 PM
    drill motor, pulley, sprocket, witch
    • Replies: 2
    • Views: 136
    01-13-2021, 09:30 AM Go to last post
  3. Spindle bearing preload issue?

    Started by QuinnSjoblom‎, 01-07-2021 12:35 PM
    finish, nose, outer, race, spindle
    • Replies: 9
    • Views: 245
    01-07-2021, 11:35 PM Go to last post
  4. Moving Gantry column bearing spacing - open discussion

    Started by peteeng‎, 10-03-2020 08:11 AM
    2 Pages
    1 2
    • Replies: 35
    • Views: 1,483
    12-25-2020, 05:24 AM Go to last post
  5. Lets build Computer Controlled Graphical Fountains

    Started by Khalid‎, 02-12-2011 02:08 PM
    17 Pages
    1 2 3 4 5 ... 17
    • Replies: 322
    • Views: 77,183
    12-13-2020, 11:31 AM Go to last post
    • Replies: 13
    • Views: 1,397
    12-01-2020, 06:38 AM Go to last post
  6. I-beam bridge design - my head is spinning...

    Started by WRMorrison‎, 06-30-2020 12:26 PM
    bridge, i-beam, i-beams, max, support
    • Replies: 2
    • Views: 652
    11-19-2020, 06:57 AM Go to last post
  7. Problem- Trapezoidal thread issues

    Started by chris-bond‎, 11-18-2020 05:26 AM
    engineering, nut, screw, tighten, torque
    • Replies: 0
    • Views: 236
    11-18-2020, 05:26 AM Go to last post
  8. Need help designing a machine to cut timber wood

    Started by cncuy‎, 10-31-2020 04:59 PM
    • Replies: 2
    • Views: 483
    10-31-2020, 10:12 PM Go to last post
  9. Stress relieving weldment in wood fire

    Started by catahoula‎, 10-28-2020 04:36 PM
    • Replies: 11
    • Views: 418
    10-29-2020, 09:10 PM Go to last post
  10. Epoxy granite but graphite?

    Started by yoobsterlol‎, 02-25-2019 01:45 AM
    • Replies: 17
    • Views: 1,988
    10-23-2020, 10:43 AM Go to last post
  11. Ideas for a punch and die assembly

    Started by msavcic‎, 09-13-2020 05:37 AM
    • Replies: 5
    • Views: 310
    09-13-2020, 09:56 PM Go to last post
  12. Question Buttress or NPTF Pipe threads

    Started by pyrotalk‎, 08-21-2020 04:51 PM
    • Replies: 0
    • Views: 313
    08-21-2020, 04:51 PM Go to last post
  13. Damping Test of Concrete & Steel Tube

    Started by ssashton‎, 07-02-2020 10:48 AM
    • Replies: 9
    • Views: 775
    08-21-2020, 12:22 AM Go to last post
  14. Ratio of mass between gantry and base table

    Started by catahoula‎, 08-09-2020 06:38 PM
    gantry, mass, mm/min, ratio, table
    • Replies: 11
    • Views: 644
    08-19-2020, 08:20 PM Go to last post
  15. Fit tolerance calculation

    Started by birdtrick‎, 07-23-2020 07:39 PM
    94mm, end, fit, range, tolerance
    • Replies: 7
    • Views: 558
    07-25-2020, 03:13 PM Go to last post
    • Replies: 4
    • Views: 407
    07-20-2020, 04:37 AM Go to last post

Page 1 of 103 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 30 users browsing this forum. (0 members & 30 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands