Mechanical Calculations/Engineering Design


Page 1 of 103 12341151101 ... LastLast
Threads 1 to 20 of 2049

Forum: Mechanical Calculations/Engineering Design

Discuss general mechanical design and mechanical calculations.

  1. Sticky Threads
  2. Sticky Thread Sticky: PLEASE READ BEFORE POSTING IN THIS FORUM!

    Started by svenakela‎, 09-12-2007 03:00 AM
    its, regards
    • Replies: 0
    • Views: 12,441
    09-12-2007, 03:00 AM Go to last post
  3. Forum Threads
  1. Mechanical Components--Harmonic Drive Gear

    Started by Allmotors‎, 01-26-2021 03:36 AM
    harmonic drive
    • Replies: 0
    • Views: 97
    01-26-2021, 03:36 AM Go to last post
    • Replies: 2
    • Views: 196
    01-20-2021, 06:24 PM Go to last post
  2. Question Newbie- What dimension/gauge steel tubing do I need for a bed frame?

    Started by mattru‎, 01-19-2021 11:26 PM
    angle, beams, bed, deflection, posts
    • Replies: 1
    • Views: 118
    01-20-2021, 01:10 AM Go to last post
  3. Designing servo driven bt30 setup

    Started by QuinnSjoblom‎, 08-04-2020 11:47 AM
    3 Pages
    1 2 3
    • Replies: 42
    • Views: 2,092
    01-18-2021, 11:30 AM Go to last post
  4. Question Pulley/Socket Size Calculations Needed

    Started by jlbenn01‎, 01-11-2021 01:35 PM
    drill motor, pulley, sprocket, witch
    • Replies: 2
    • Views: 146
    01-13-2021, 09:30 AM Go to last post
  5. Spindle bearing preload issue?

    Started by QuinnSjoblom‎, 01-07-2021 12:35 PM
    finish, nose, outer, race, spindle
    • Replies: 9
    • Views: 269
    01-07-2021, 11:35 PM Go to last post
  6. Moving Gantry column bearing spacing - open discussion

    Started by peteeng‎, 10-03-2020 08:11 AM
    2 Pages
    1 2
    • Replies: 35
    • Views: 1,511
    12-25-2020, 05:24 AM Go to last post
  7. Lets build Computer Controlled Graphical Fountains

    Started by Khalid‎, 02-12-2011 02:08 PM
    17 Pages
    1 2 3 4 5 ... 17
    • Replies: 322
    • Views: 77,275
    12-13-2020, 11:31 AM Go to last post
    • Replies: 13
    • Views: 1,432
    12-01-2020, 06:38 AM Go to last post
  8. I-beam bridge design - my head is spinning...

    Started by WRMorrison‎, 06-30-2020 12:26 PM
    bridge, i-beam, i-beams, max, support
    • Replies: 2
    • Views: 660
    11-19-2020, 06:57 AM Go to last post
  9. Problem- Trapezoidal thread issues

    Started by chris-bond‎, 11-18-2020 05:26 AM
    engineering, nut, screw, tighten, torque
    • Replies: 0
    • Views: 241
    11-18-2020, 05:26 AM Go to last post
  10. Need help designing a machine to cut timber wood

    Started by cncuy‎, 10-31-2020 04:59 PM
    • Replies: 2
    • Views: 507
    10-31-2020, 10:12 PM Go to last post
  11. Stress relieving weldment in wood fire

    Started by catahoula‎, 10-28-2020 04:36 PM
    • Replies: 11
    • Views: 429
    10-29-2020, 09:10 PM Go to last post
  12. Epoxy granite but graphite?

    Started by yoobsterlol‎, 02-25-2019 01:45 AM
    • Replies: 17
    • Views: 2,003
    10-23-2020, 10:43 AM Go to last post
  13. Ideas for a punch and die assembly

    Started by msavcic‎, 09-13-2020 05:37 AM
    • Replies: 5
    • Views: 313
    09-13-2020, 09:56 PM Go to last post
  14. Question Buttress or NPTF Pipe threads

    Started by pyrotalk‎, 08-21-2020 04:51 PM
    • Replies: 0
    • Views: 315
    08-21-2020, 04:51 PM Go to last post
  15. Damping Test of Concrete & Steel Tube

    Started by ssashton‎, 07-02-2020 10:48 AM
    • Replies: 9
    • Views: 793
    08-21-2020, 12:22 AM Go to last post
  16. Ratio of mass between gantry and base table

    Started by catahoula‎, 08-09-2020 06:38 PM
    gantry, mass, mm/min, ratio, table
    • Replies: 11
    • Views: 664
    08-19-2020, 08:20 PM Go to last post
  17. Fit tolerance calculation

    Started by birdtrick‎, 07-23-2020 07:39 PM
    94mm, end, fit, range, tolerance
    • Replies: 7
    • Views: 576
    07-25-2020, 03:13 PM Go to last post

Page 1 of 103 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 30 users browsing this forum. (0 members & 30 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands