Angle Iron Load capacity...


Results 1 to 13 of 13

Thread: Angle Iron Load capacity...

  1. #1
    Member
    Join Date
    Mar 2010
    Location
    United States
    Posts
    564
    Downloads
    0
    Uploads
    0

    Default Angle Iron Load capacity...

    I'm working on moving a compact washer dryer upstairs and want to support my dryer with some angle iron but can't find a chart with some type of load capacity, my math is not good I confess...

    I want to use .250 hot rolled angle iron 3" x 3" x 24" attached to my walls to support a dryer weighing in under 100 lbs. I don't think this will be an issue but would love some confirmation on the idea... angle iron is the best fit due to some space limitations.

    I've sketched up a drawing to help visualize my problem.

    Any help would be appreciated.

    Adam,


    Angle Iron Load capacity...-snag-0325-jpg

    Similar Threads:
    G540, Rack and Pinion Drives-X/Y axis, 1/2-Ball Screw-Z Axis w/THK HSR 25 Linear Slides, Steppers KL23H2100-35-4B, Power Supply-KL-600-48


  2. #2
    Member Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    3979
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    24 inches of 3x3x0.250 angle would support a car. No problem for a 100 lb dryer.

    Jim Dawson
    Sandy, Oregon, USA


  3. #3
    Member
    Join Date
    Mar 2010
    Location
    United States
    Posts
    564
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    Appreciate the response... I kind of figured the weight wouldn't be a problem.

    Adam,

    G540, Rack and Pinion Drives-X/Y axis, 1/2-Ball Screw-Z Axis w/THK HSR 25 Linear Slides, Steppers KL23H2100-35-4B, Power Supply-KL-600-48


  4. #4
    Member peteeng's Avatar
    Join Date
    Jul 2018
    Location
    dum dum
    Posts
    1028
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    Hi Adam - The steel angle is not a problem just don't hold it on with chewing gum. So use adequate screws/bolts etc Peter



  5. #5
    Member
    Join Date
    Mar 2010
    Location
    United States
    Posts
    564
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    LOL!
    Quote Originally Posted by peteeng View Post
    Hi Adam - The steel angle is not a problem just don't hold it on with chewing gum. So use adequate screws/bolts etc Peter
    Plan is to bolt it to the studs... could I also flip the angle with similar results?

    Angle Iron Load capacity...-snag-0327-jpg

    Out of curiosity, what is the appx. weight max that angle can hold across the entire piece when bolted against a wall similar to this?

    Adam,

    G540, Rack and Pinion Drives-X/Y axis, 1/2-Ball Screw-Z Axis w/THK HSR 25 Linear Slides, Steppers KL23H2100-35-4B, Power Supply-KL-600-48


  6. #6
    Member Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    3979
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    A lot. Here is an example of a 5000 lb mill sitting on 4x4x3/8 angle. Those angles are bolted on with three 3/8 bolts each. I did not do this, but it seems to work fine. I've rolled it all over my shop.

    Angle Iron Load capacity...-img_0268-jpg

    Bolted to the wall as you show would support several hundred lbs safely. I think the studs would be the weak point.

    Attached Thumbnails Attached Thumbnails Angle Iron Load capacity...-img_0268-jpg  
    Jim Dawson
    Sandy, Oregon, USA


  7. #7
    Member
    Join Date
    Mar 2010
    Location
    United States
    Posts
    564
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    OK, then I'm good with the Angle...

    Last question on the subject is 1/4" over kill??? should I be looking more in the neighborhood of 3/16" or 1/8"??

    Thanks.

    Adam,

    G540, Rack and Pinion Drives-X/Y axis, 1/2-Ball Screw-Z Axis w/THK HSR 25 Linear Slides, Steppers KL23H2100-35-4B, Power Supply-KL-600-48


  8. #8
    Member Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    3979
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    I think 1/8 would support a dryer just fine. My full sized dryer weighs about 50 or so lbs. I think your biggest problem is going to be finding enough studs to screw into, just depends on how the walls were constructed.

    Jim Dawson
    Sandy, Oregon, USA


  9. #9
    Member
    Join Date
    Mar 2010
    Location
    United States
    Posts
    564
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    That's one light full size Dryer...

    No worries with me mounting the Angle upside down either, correct? It doesn't impact the structural integrity of the iron by doing that?

    G540, Rack and Pinion Drives-X/Y axis, 1/2-Ball Screw-Z Axis w/THK HSR 25 Linear Slides, Steppers KL23H2100-35-4B, Power Supply-KL-600-48


  10. #10
    Member Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    3979
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    Either way will work. In either case you want the screws near the top.

    Jim Dawson
    Sandy, Oregon, USA


  11. #11
    Member
    Join Date
    Mar 2010
    Location
    United States
    Posts
    564
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    Thanks for the assistance.

    Adam,

    G540, Rack and Pinion Drives-X/Y axis, 1/2-Ball Screw-Z Axis w/THK HSR 25 Linear Slides, Steppers KL23H2100-35-4B, Power Supply-KL-600-48


  12. #12
    Member Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    3979
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    My pleasure. You're welcome

    Jim Dawson
    Sandy, Oregon, USA


  13. #13
    Member
    Join Date
    Sep 2011
    Location
    USA
    Posts
    100
    Downloads
    0
    Uploads
    0

    Default Re: Angle Iron Load capacity...

    1/8" would be more than enough for support the load. I think you could even get by with something as thin as 16 GA. This is also going to be dependent on where the dryer is positioned on the angle iron. The further away from the wall the thicker the material needs to be.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Angle Iron Load capacity...

Angle Iron Load capacity...

Angle Iron Load capacity...