you are have parameter of machine?
Can anybody help me to find out how to inital parameter on meldas 300 series??
because I have a problem with my machine and it need to initial first...
my NC system 320 M
this machine have NC alarm like:
S02 INITIAL PARAM ERROR DIAGN 46
Y03 AMP. UNEQUIPPED DIAGN UVW
EMG EMERGENCY DIAGN SRV
Z51 EE ROM ERROR
pls anybody help me on this situation...
Similar Threads:
Last edited by gunawan_tehnik; 12-15-2008 at 01:56 AM.
you are have parameter of machine?
1) Save all of your machine data to disk.
a) Tool data.
b) Machine programs.
c) Work offsets.
d) Common variables.
e) Parameters.
2) Go back to “Machine parameters”
3) Find “fix_P”
4) Set it to a “1”
5) Go to “Data I/O”
6) Go to “Erase”
7) In “Data( )” type “FORMAT”
8) Go to “Input”
9) In “#( )” type “4”
10) Press <input> key.
11) Power the NC off and then back on.
12) Reload all of the saved data.
I have an error also with a MELDAS 300 SERIES.
Alarm Message 35 Cut off wire heat displace.
I have no idea what this is trying to tell me.
The Machine is a Mitsubishi M-V65B
Any help would be greatly appreciated.
please check the drive communication cable.
note: the problem due to drive is not communicating with NC . may be one drive is not getting on. i think the error is not related with NC. this depends on drive malfunction or faulty please .
CNC MANUALS
pls i have alarm "A103 thermokompensation
Hi All
I have TRAUB TND 200 with TX8F (Meldas Mitshubishi)
I put all parameters directly from the Papers orginal together with the machine.
Still fight with Parametres for SEVO I have two red errors
S01 SERVO ALARM:PR 0027
SY03 AMP. UNEQUIPPED S1
And one yelow
M02 NEED R.P. RTN 0004
Any one have any information about how to set up the servo?
I try to put some data according to some papers with servo together but nAttachment 442123o changes
The problem which I find t was with Parameters 35 & 36 and also 57-64
If any one have something from SERVICE manual with discription of parameters it will be helpfull.
hey do you still need help. shoot me a text ill walk you through it i have all backups 8325633063
Hello Every One.
Have You ever problems with diven tools motor ? I find in my TRAUB TND 200 AL 25 I suspect card on FR-SF-2-11K-T but need some kind of electronic to check all the Amplifeir FREQROL FR-SFJ.
If some one need it parameters for TND 200 or TND 300. I have it
Check your manuals.... The parameters are almost always part of the documentation set the machine integrator provides. Alternatively, the parameters are written into EEPROM (95% sure), so you rarely actually have to re-enter them. HOWEVER, the RAM will lose its memory if you lose power. You will need to reformat that, but this process won't change the parameters. You *will* lose any macros that are in memory, though. That can include tool change macros, if the machine builder used macros as a means of controlling tool change (sometimes they integrate with the PLC, and that is usually in EPROM).
I would highly recommend that you SAVE your parameters, even if you think that they are lost, BEFORE you do anything else. You may very well realize that the data is still in the machine any that you lost it when you tried installing someone else's parameters. That would be highly unfortunate. There is zero downside to saving the parameters before you screw around with the machine. Just my 2 cents.
Yes, i have the parameters in my manual. The problem is that i don't have Parameter Nr.12 - select bits. There are the machine options in binary code. It is just empty space for this values in the parameter book. Without this i just can't become the ready on the machine.