Need Help! ECOCA - MELDAS MAGIC 64L


Results 1 to 8 of 8

Thread: ECOCA - MELDAS MAGIC 64L

  1. #1
    Member
    Join Date
    Jan 2007
    Location
    india
    Posts
    93
    Downloads
    0
    Uploads
    0

    Default ECOCA - MELDAS MAGIC 64L

    ALARM: EMERGENCY EXIN
    M01 OPERATION ERROR XZ


    Detail of machine are as under,


    NC - MELDAS MAGIC 64L
    PC - MAGIC Pro-HI/L ( INTL) BDD - A02 W016 - A0
    PLC - ECOCA - ELALL - M5
    SYSTEM ID - 2090745880



    In this machine, system power supply gone bad. We replaced the supply , now we are facing following alarms,
    EMERGENCY EXIN

    M01 OPERATION ERROR XZ

    According to the electrical diagram, hard over travel switches are optional & are missing in machine.
    In diagnosis mode, checked other inputs like cycle start , mode change switch which are ok.
    Surprisingly no any out put is being generated.
    Tried to check the PLC ladder but it is not being open. When searched any input like X29 or similar it shows ERROR.
    When tried to check PLC size it shows
    LINK 0 / KBYTE
    LADDER 0 / KB
    MESSAGE 0/ KB
    I loaded all data by floppy even then it shows the same alarm. ( path c:/ncbac )

    Next Day Work:

    To-day I reloaded all the data, but still no improvement & same alarm is being displayed.
    In Meldas Magic screen tried to open the PLC ladder.
    Sequence ... Ctr + F , Menu , 9main, monitor , NO / NC , X1F & enter it shows Prog not found.


    When I tried to search by Rung No. 100,
    PLC ladder is being displayed but when I checked whole ladder, no any X or Y contact was found.


    I am quite confused, pl help.
    In seven segment display of controller it shows " A "


    ( Can we load the data with the help of RS232 port.)

    PL send your suggestion to solve the problem..

    Thanks

    Similar Threads:


  2. #2
    Registered Russell840's Avatar
    Join Date
    Jul 2016
    Location
    Northern Mariana Islands
    Posts
    108
    Downloads
    0
    Uploads
    0

    Unhappy Re: ECOCA - MELDAS MAGIC 64L

    Hi there
    Dear advantures , I have a milling machine , whitch work with meldas magic64.
    as I read in manuals , After installing softwars , transfer parameters on " HI-M " ,I need to set and adjust the NC parameters conforming to the machine configuration and machine specifications.
    Unfortonatly I dont Know How?



  3. #3
    Registered Russell840's Avatar
    Join Date
    Jul 2016
    Location
    Northern Mariana Islands
    Posts
    108
    Downloads
    0
    Uploads
    0

    Default Re: ECOCA - MELDAS MAGIC 64L

    [QUOTE=Russell840;1956302]Hi there
    Dear advantures , I have a milling machine , whitch work with meldas magic64.
    as I read in manuals , After installing softwars , transfer parameters on " HI-M " ,I need to set and adjust the NC parameters conforming to the machine configuration and machine specifications.
    Unfortonatly I dont Know How?



    Finally I found the answer , and run the machine
    Well, if there is any quastion , its my plasure to help.
    Best regurds
    Russell



  4. #4
    Member
    Join Date
    Feb 2005
    Location
    pakistan
    Posts
    28
    Downloads
    0
    Uploads
    0

    Default

    Hi Russell840

    I need your help

    I have a hartford machining center, whitch work with meldas magic64.

    I need system floppys

    Meldas magic64 nc system disk 1 and 2
    Meldas magic utility disk 1 and 2
    Meldas magic meldasmagic monitor disk 1
    Meldas magic custom API library runtime disk 1 and 2
    Meldas magic64 NC data 64m disk 1

    Please help me
    If u have these floppy's please send me a soft copy

    My email. informton@yahoo.com
    Thanks in advance



  5. #5
    Member
    Join Date
    Feb 2005
    Location
    pakistan
    Posts
    28
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by Kashif View Post
    Hi Russell840

    I need your help

    I have a hartford machining center, whitch work with meldas magic64.

    I need system floppys

    Meldas magic64 nc system disk 1 and 2
    Meldas magic utility disk 1 and 2
    Meldas magic meldasmagic monitor disk 1
    Meldas magic custom API library runtime disk 1 and 2
    Meldas magic64 NC data 64m disk 1

    Please help me
    If u have these floppy's please send me a soft copy

    My email. informton@yahoo.com
    Thanks in advance

    Mitsubishi Meldas Magic64 PC Based
    System SoftWare Disk

    AOMEI complete disk image

    https://drive.google.com/drive/mobile/folders/1ENcGRNDRlsExITohcSXAEkZUd5pFOblP?usp=sharing



  6. #6
    Jaanus50's Avatar
    Join Date
    Feb 2023
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: ECOCA - MELDAS MAGIC 64L

    I have a Ecoca el4615, unfortunatly windows battery goes empty and after that Magicpro HI/L gives fault "Protection key not found" . Machine is working on Magicmon. Somewhere should be protection key file. Any ideas?



  7. #7
    Member Semoogad's Avatar
    Join Date
    Feb 2021
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default

    [QUOTE=Russell840;1963822]
    Quote Originally Posted by Russell840 View Post
    Hi there
    Dear advantures , I have a milling machine , whitch work with meldas magic64.
    as I read in manuals , After installing softwars , transfer parameters on " HI-M " ,I need to set and adjust the NC parameters conforming to the machine configuration and machine specifications.
    Unfortonatly I dont Know How?



    Finally I found the answer , and run the machine
    Well, if there is any quastion , its my plasure to help.
    Best regurds
    Russell




  8. #8
    Member Semoogad's Avatar
    Join Date
    Feb 2021
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default

    [QUOTE=Russell840;1963822]
    Quote Originally Posted by Russell840 View Post
    Hi there
    Dear advantures , I have a milling machine , whitch work with meldas magic64.
    as I read in manuals , After installing softwars , transfer parameters on " HI-M " ,I need to set and adjust the NC parameters conforming to the machine configuration and machine specifications.
    Unfortonatly I dont Know How?



    Finally I found the answer , and run the machine
    Well, if there is any quastion , its my plasure to help.
    Best regurds
    Russell





    Hello
    Can u help i have the same emg exin in my machine how to solve



  9. #9
    Member malego's Avatar
    Join Date
    Sep 2023
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: ECOCA - MELDAS MAGIC 64L

    Quote Originally Posted by Jaanus50 View Post
    I have a Ecoca el4615, unfortunatly windows battery goes empty and after that Magicpro HI/L gives fault "Protection key not found" . Machine is working on Magicmon. Somewhere should be protection key file. Any ideas?
    Did you fix your problem? I have the exact same error message :"Protection key not found".
    I installed everything from scratch on a new PC. Everything works fine as far as the Meldasmagic configuration and startup.
    Only Magicpro HI/L is complaining at startup saying the :"Protection key not found".
    I can't find any "key" or registry entry or file for that...
    Any one can help?



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

ECOCA - MELDAS MAGIC 64L

ECOCA - MELDAS MAGIC 64L