Dust collection mod question

Results 1 to 5 of 5

Thread: Dust collection mod question

  1. #1
    Member
    Join Date
    Jun 2017
    Posts
    369
    Downloads
    0
    Uploads
    0

    Default Dust collection mod question

    I purchased harbor freight 2hp dust collector, Weinn industries filter and a super dust deputy to do the mod that everyone seems to be doing on YouTube & everything seems to be going ok but my issue is this.

    My building that the router is in has a low ceiling and once the weinn filter is installed with the filter inlet in line with the exhaust port of the dust collection motor it will need to be removed everytime the drum needs emptied.

    Does the inlet need to be in a straight line with the exhaust? If I raise it up to the ceiling I could get the drum out without removing the weinn filter.

    Thank you
    Gary

    I'm not sure why the photo is rotated it is correct in my gallery

    Dust collection mod question-20181124_161534-jpg

    Similar Threads:
    Last edited by Gary-Wiant; 11-24-2018 at 07:56 PM. Reason: Photo rotated


  2. #2
    Community Moderator Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    5717
    Downloads
    0
    Uploads
    0

    Default Re: Dust collection mod question

    Normally the blower/motor system can be located anywhere, so you could have it located to the side of the cyclone and connected with an elbow, so any plumbing that would get it out of the way would work. But keep in mind that each elbow slightly reduces the system airflow.

    Jim Dawson
    Sandy, Oregon, USA


  3. #3
    Member
    Join Date
    Jun 2017
    Posts
    369
    Downloads
    0
    Uploads
    0

    Default Re: Dust collection mod question

    Jim, ok thank you. I'm going to see how far out of the way I can get the filter.

    Thanks again
    Gary



  4. #4
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: Dust collection mod question

    You can put the filter anywhere, but the straighter the better. Try to avoid 90° bends.
    People do what's known as the "Stovepipe Mod" to reduce restriction between the blower and filter.

    https://www.sawdustzone.org/forum/di...-stovepipe-mod

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  5. #5
    Member
    Join Date
    Jun 2017
    Posts
    369
    Downloads
    0
    Uploads
    0

    Default Re: Dust collection mod question

    Gerry - Thank you I'll use the stovepipe mod. Even if it doesnt get the filter out of the way enough to keep me from having to remove the filter it seems to make a big difference in performance.

    Thanks again
    Gary



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Dust collection mod question

Dust collection mod question