Machines running Mach Software


Page 1 of 43 123411 ... LastLast
Threads 1 to 20 of 847

Forum: Machines running Mach Software

Discuss your set-up and experiences running your machine using Mach software here.

  1. Mach3, ESS, & Spindle Motor Tuning

    Started by kolias‎, 01-01-2023 06:43 PM
    change, motor, parameters, spindle, tuning
    • Replies: 2
    • Views: 587
    01-02-2023, 03:49 PM Go to last post
  2. BL-USBMACH-WS-3.25 Output not working

    Started by cusna‎, 10-26-2021 06:05 AM
    • Replies: 4
    • Views: 1,205
    12-02-2022, 11:28 AM Go to last post
  3. Ref All Home, Slaved axis does not synch.

    Started by hkinkade‎, 11-01-2022 05:08 PM
    axis, home, jog, ref, slave
    • Replies: 0
    • Views: 430
    11-01-2022, 05:08 PM Go to last post
  4. Jerky Axis Moves on Curves

    Started by kolias‎, 10-17-2022 04:26 AM
    cnc, curves, jerky, lines, straight
    • Replies: 2
    • Views: 473
    10-17-2022, 07:13 PM Go to last post
    • Replies: 0
    • Views: 598
    07-25-2022, 12:53 AM Go to last post
  5. Need Help!- Mach4 v 4809

    Started by edcross‎, 07-14-2022 08:33 AM
    controller, ess, gecko, mach4, smoothstepper
    • Replies: 1
    • Views: 486
    07-14-2022, 06:35 PM Go to last post
  6. Question Connecting an Electronic type kinematic Probe

    Started by kawazuki‎, 07-14-2022 09:36 AM
    • Replies: 0
    • Views: 389
    07-14-2022, 09:36 AM Go to last post
  7. Mitsubishi AC Servo Spindle Retrofit

    Started by jlmccuan‎, 04-04-2022 09:26 AM
    2 Pages
    1 2
    • Replies: 39
    • Views: 2,027
    05-18-2022, 05:45 PM Go to last post
  8. Problem- Using Mach3 to keep spindle from cutting my fingers off

    Started by Igloomason‎, 04-16-2022 10:47 AM
    pin, pins, safety, spindle, superpid
    • Replies: 4
    • Views: 681
    04-16-2022, 01:25 PM Go to last post
  9. mach 3 settings help

    Started by MrAbrasive‎, 04-06-2022 06:14 PM
    c41, control, software, speed, spindle
    • Replies: 2
    • Views: 552
    04-07-2022, 11:05 AM Go to last post
  10. Need Help!- Cannot move any Axis

    Started by zappafan1‎, 03-27-2022 01:37 PM
    add-in, card, cnc, gecko, purchased
    • Replies: 4
    • Views: 516
    03-28-2022, 06:59 PM Go to last post
  11. replaced my x/p machine with another x/p

    Started by kjl-pdx‎, 03-12-2022 08:41 PM
    cnc, mach3, machine, x/p, years
    • Replies: 0
    • Views: 513
    03-12-2022, 08:41 PM Go to last post
  12. New Machine Build- Slave axis is not synchronized with master

    Started by Antrac1t‎, 12-29-2015 02:12 PM
    axis, master, motor, slave, stepper
    • Replies: 4
    • Views: 2,672
    02-07-2022, 10:50 AM Go to last post
  13. Mach3 Tuning

    Started by RufusToad‎, 11-28-2021 02:34 PM
    axis, set, settings, steps, tuning
    • Replies: 0
    • Views: 595
    11-28-2021, 02:34 PM Go to last post
  14. Mach 3 hangs while generating toolpath

    Started by jet8300‎, 11-07-2021 08:42 PM
    software, toolpath, gcode, mach, generating
    • Replies: 5
    • Views: 692
    11-08-2021, 02:30 PM Go to last post
  15. Need Help!- Rockey4USB Key not found on Windows XP

    Started by Qaisar‎, 10-26-2021 07:48 AM
    • Replies: 0
    • Views: 504
    10-26-2021, 07:48 AM Go to last post
  16. Using old hard drive to copy Mach3 Config file

    Started by ecope‎, 10-18-2021 08:45 AM
    cnc, computer, drive, hard, mach3
    • Replies: 1
    • Views: 747
    10-18-2021, 02:57 PM Go to last post
    • Replies: 9
    • Views: 3,149
    10-14-2021, 05:25 AM Go to last post
  17. Thermwood Mach conversion?

    Started by MArruda‎, 02-03-2011 10:26 PM
    cnc.
    • Replies: 9
    • Views: 1,832
    10-13-2021, 06:04 AM Go to last post
  18. Problem- Mach 3 XML code issue

    Started by zappafan1‎, 09-21-2021 12:49 AM
    code, file, lines, similar, xml
    • Replies: 0
    • Views: 746
    09-21-2021, 12:49 AM Go to last post

Page 1 of 43 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 4 users browsing this forum. (0 members & 4 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands