Spindle works only after closing and opening the mach3


Results 1 to 7 of 7

Thread: Spindle works only after closing and opening the mach3

  1. #1
    Member
    Join Date
    Jan 2017
    Location
    United Arab Emirates
    Posts
    84
    Downloads
    0
    Uploads
    0

    Default Spindle works only after closing and opening the mach3

    Hi there

    In my previous post I think i couldn't explain clearly my Spindle problem,
    My spindle works only after I close and open the mach3, By doing so (opening the mach3), I noticed that in "Spindle Speed" Section of the First Tab (Program RunAlt-1) As you know there is a Button by name of "Spindle CW F5" and under this buttom there are some DROs that one can Enter RPM in it The RPM Values are "at the time of opening" all Zeros. At this point If I push the "Spindle CW F5" Button and then enter some RPM values in "spindle speed" DRO , The Spindle starts Running and I can Increase or decrease its RPM speed.

    But If I try to run a code like usual which is by loading a G Code program and then pushing the start Button, The axis move But My Spindle would not start, It appears that the spindle does not respond to the M3 Command of the G code, and at this point even if I push the "Spindle CW F5" Button, the Spindle would not start, also the DROs under this "Spindle CW F5" Button have some values in them from the G code that even if I try to change them they would not change. At this point I have to Close and open The Mach3 in order to start the spindle.

    Any recommendations or suggestions that what is going on here?
    should mention that all these happened recently, It was working Fine before.

    Regards
    Jhonansaro

    Similar Threads:


  2. #2
    Member
    Join Date
    Jan 2017
    Location
    United Arab Emirates
    Posts
    84
    Downloads
    0
    Uploads
    0

    Default Re: Spindle works only after closing and opening the mach3

    Hi every Body

    Please any recommendation would be greatly appreciated.

    regards
    Jhonansaro



  3. #3

    Default Re: Spindle works only after closing and opening the mach3

    I have this exact issue any fixes?



  4. #4
    Member
    Join Date
    Nov 2013
    Posts
    4282
    Downloads
    0
    Uploads
    0

    Default Re: Spindle works only after closing and opening the mach3

    Hi,
    all development on Mach3 ceased six years ago....do yourself a favor and upgrade to Mach4.

    Craig



  5. #5
    Member Michael82's Avatar
    Join Date
    Nov 2007
    Location
    usa
    Posts
    361
    Downloads
    0
    Uploads
    0

    Default Re: Spindle works only after closing and opening the mach3

    Quote Originally Posted by johnansaro View Post
    Hi every Body

    Please any recommendation would be greatly appreciated.

    regards
    Jhonansaro
    This is just a shot in the dark do you have your spindlle relay output triggers set ? in the spindle setup page under ports and pins ?



  6. #6
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Spindle works only after closing and opening the mach3

    Quote Originally Posted by johnansaro View Post
    Hi there

    In my previous post I think i couldn't explain clearly my Spindle problem,
    My spindle works only after I close and open the mach3, By doing so (opening the mach3), I noticed that in "Spindle Speed" Section of the First Tab (Program RunAlt-1) As you know there is a Button by name of "Spindle CW F5" and under this buttom there are some DROs that one can Enter RPM in it The RPM Values are "at the time of opening" all Zeros. At this point If I push the "Spindle CW F5" Button and then enter some RPM values in "spindle speed" DRO , The Spindle starts Running and I can Increase or decrease its RPM speed.

    But If I try to run a code like usual which is by loading a G Code program and then pushing the start Button, The axis move But My Spindle would not start, It appears that the spindle does not respond to the M3 Command of the G code, and at this point even if I push the "Spindle CW F5" Button, the Spindle would not start, also the DROs under this "Spindle CW F5" Button have some values in them from the G code that even if I try to change them they would not change. At this point I have to Close and open The Mach3 in order to start the spindle.

    Any recommendations or suggestions that what is going on here?
    should mention that all these happened recently, It was working Fine before.

    Regards
    Jhonansaro
    How do you have the spindle start up written in your program ??

    Cut / Copy / Paste your program here, you only need the start up part of your program

    There are more than one thing that can cause this so start with the program

    Mactec54


  7. #7
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Spindle works only after closing and opening the mach3

    Quote Originally Posted by joeavaerage View Post
    Hi,
    all development on Mach3 ceased six years ago....do yourself a favor and upgrade to Mach4.

    Craig
    There are still thousands using it all over the world and it works well for most users

    Mactec54


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Spindle works only after closing and opening the mach3

Spindle works only after closing and opening the mach3