Mach 3 stops executing code in middle of run


Results 1 to 8 of 8

Thread: Mach 3 stops executing code in middle of run

  1. #1
    Member
    Join Date
    May 2018
    Location
    United States
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default Mach 3 stops executing code in middle of run

    Not sure what is happening here, but I am running a simple inlay code from Vcarve Pro. Part way through the run, the CNC shuts down. Same place every time. CNC Router Parts Pro4848. Does not appear to be an error code anywhere in Mach 3 that I can find. The "Flood" light is flashing? Not sure why as I don't have a liquid-cooled spindle.

    So, is this a Mach 3 issue or something in the VCarve?

    Insight on where to look would be appreciated!

    Stan

    Similar Threads:


  2. #2
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: Mach 3 stops executing code in middle of run

    Does it stop at or near line 500?
    If so, it's because Mach3 is in demo mode.

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  3. #3
    Member
    Join Date
    May 2018
    Location
    United States
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default Re: Mach 3 stops executing code in middle of run

    Not sure, I will check. What does that mean? Used it yesterday without incident, so not sure what changed??



  4. #4
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: Mach 3 stops executing code in middle of run

    That would mean the license is not working.
    Does it say Licensed to (your name) in the Title bar?

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  5. #5
    Member
    Join Date
    May 2018
    Location
    United States
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default Re: Mach 3 stops executing code in middle of run

    Yes, still shows as licensed to me.



  6. #6
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: Mach 3 stops executing code in middle of run

    Were there any messages when it stopped?
    Are you using a parallel port, or a motion controller? If a controller, which one?

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  7. #7
    Member
    Join Date
    May 2018
    Location
    United States
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default Re: Mach 3 stops executing code in middle of run

    Just tried a totally separate file generated in Vcarve Pro and it executed fine, so I assume it must be something in the original code?

    No obvious error messages. Gantry just stops and the spindle spools down, same place every time.

    I'm going to re-generate the G-code from Vcarve and try it again.

    Thanks for your ideas on things to check!



  8. #8
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: Mach 3 stops executing code in middle of run

    There should be a message on the screen.
    Is the reset button flashing when it stops?

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Mach 3 stops executing code in middle of run

Mach 3 stops executing code in middle of run