Pallol,
Try this and report back the outcome.
Jeff...
hi,
I just purchased a chinese 3040 4 axis cnc. It is a usb interface but the seller sent me the wrong plugins. The controller is not an rnr motion controller, nor a leafboy, or ecut.
i opened up the controller box and the usb board is marked BL-USBMACH-V2.1. I think that mach3 control plugin selector sees it as usbmach v2 if i have the proper plugin
i can find plenty of these up for sale with the driver cd, but cannot find the software on its own.
can any one point me to a link for the mach3 plugin for this controller please?
I don’t think the seller has a clue what “brand” of controller i have
cheers
Similar Threads:
Pallol,
Try this and report back the outcome.
Jeff...
Patience and perseverance have a magical effect before which difficulties disappear and obstacles vanish.
Thanks Jeff, didn’t work, no motion controller connected.
from my research, this driver is for the card that has both usb and parallel ports, mine has just the one usb port.
might be best to splash out the $30-40 on a new card, at least it would come with a driver disc and I’ll have a spare
the wait for it is gunna kill but
Sent from my iPad using Tapatalk
Pallol,
Please post a few good images of the board you have so that we may better assist you.
Jeff...
Patience and perseverance have a magical effect before which difficulties disappear and obstacles vanish.
pictures
Sent from my iPad using Tapatalk
Pallol,
This should do the trick, either way please post your results so we may help others in the future.
Jeff...
Patience and perseverance have a magical effect before which difficulties disappear and obstacles vanish.
I have the same controller, same issues, so THANKS, helped me a lot too.
Last edited by djnimbusnz; 06-24-2018 at 07:08 AM.
Hi friends I have the same board but it is not working with above dll. Which versions of windows(32 or 64 bit) and mach3 are using?
My windows = Windows 7 64 bit
Mach3 = Version3.043.066
Board = BL-USBMach v2.0 D1712
Is there another dll about it?
I have the same board and found a driver on a Russian cnc forum. This also has a handbook for the board. I have not yet tested the dll, but the instructions make it clear that the standard parallel port driver must NOT be loaded when installing Mach 3. This was the biggest problem that came up on the russian thread.
I have trid to up load the software and data package for this board but it is too large to upload, if any body is interested post back and I will break it down into the dll and the instruction manual.
I hope this helps.
This is a link to a site with instructions for this board.
https://sites.google.com/a/u.toctai....L-UsbMach-V2-0
Settings and manuals for BL-USBMACH-V2.0 board
friends, I have this BL-USBMach v2.2 card, I am trying to use the A and B axes as servos but, I can not, I can manually work through the keyboard, configured in the keypad system but not as slaves of the X and Y axes, I've tried everything, does anyone have a solution for this?
use:
Mach3.043.066
Windows10
hi i'm from indonesia, new member here and learning about cnc, actually i got here because this thread, i allready searching and no luck, i have bl-usbmach v2.0, i think the difference with v2.1 is spindle controll port, v2.0 has 3 pin and v2.1 has 4 pin, is there possibility use the v2.0 bob with vfd?
if the answer is yes, how to connecting to vfd? because no fwd port on v2.0, and i use best fc300-2.2g vfd, verry thankfull id anyone can help me with this problems.
It is better to use this set, it is much easy to use to get it working
https://www.automationtechnologiesin...ach3-usb-card/
I'm trying to run the BL-USBMach v2.2 card with a slave axis on Mach3, it does not seem to work, it seems that in the plug-in of this board, the settings function / slave axis in mach3 is unusable, I have tried in several windows, in several versions of mach3, I have reports that others that have the same card, could not configure, I come here to ask, if anyone has been able to configure the BL-USBMach v2.2 card with slave axis in mach3 ??