@ Brett32what is not working ? The motors work right ? what else do you need help with ?
I also got this USB breakout board, and used to control my CNC lathe.
I connect the Input5 (Pin15) as index to get spindles RPM (use hall sensor to generate one pulse per revolution) ,
but it return random RPMs from 10 - 1000, not usable to.
When I use LPT breakout board, I got steady RPMs using the Pin15.
it seems this USB breakout board cannot get spindle feedback RPM.
Anyone have new driver or solution to get it work with spindle index?
Hello. Friends, please help me. My job has been disrupted due to this problem. Does anyone have the exact wiring of this controller? Send it to me on WhatsApp. + 989192558632
I was able to the spindle index working but mach 3 would lock up after i jog z axis I tried switching the driver and the problem followed so I bought new drivers still does it . I have to shut down mach 3 restart it and it will work for a little bit and it does it again . I finally switched to ess smoothstepper and all the problems went away
Hello friend
. My device is in the settings stage. The first problem is that I do not know the settings of the drives and software. The second problem is that the road controller port locks all the axles when I disconnect it from the PC, and the axles are released when I connect it. Please help
https://s4.uupload.ir/files/????????_??????_8nhm.jpg
https://s4.uupload.ir/files/drufelcnc_usbcnc5a_l30.png
https://s4.uupload.ir/files/????????_??????_ry91.jpg
https://s4.uupload.ir/files/whatsapp-image-2020-11-21-at-11.36.09-pm_y93e.jpeg
This is a photo of the parts and connector I used
Hi. quick question for the owners of this board: do you see "actual speed" in mach3 during travel or works? I see only 0.00 and so I don't know the real speed of the cnc.
Thanks a lot.
(escuse for my bad english, I'm from Italy)
Hi Michael, sent you a PM asking how you've sorted the spindle index pulse. Just got myself involved with a V2.1 board too and have yet figured out why it doesn't work. Tried to send a clean 2%, 5%, 10% duty cycle signal using a function generator and that doesn't reach out to M3 via all the BL Mach3 dll drivers I could find. Next step is probably to hook a logic analyzer on the usb (hid) protocol and reverse engineer that STM32 firmware and the plugin entirely :/
In a meantime, if anyone else managed to get this spindle index pulse working please do share. Bet many who have this board are pretty stuck... (just how the dev of that plugin thought we were doing rigid tapping and lathe threading?!)
Hi,
Esquema de ligação do PWM
Cf300
Pino 1 Porta FWD
Pino 5 Output 01
Inversor parametrizado para 0-10v igual para potenciometro
Pino 7 - AVI
Pino 8 - ACM
Pino 9 - 10v
Esquema de ligação do PWM
Cf300
Pino 1 Porta FWD
Pino 5 Output 01
Inversor parametrizado para 0-10v igual para potenciometro
Pino 7 - AVI
Pino 8 - ACM
Pino 9 - 10v
- - - Updated - - -
Esquema de ligação do PWM
Cf300
Pino 1 Porta FWD
Pino 5 Output 01
Inversor parametrizado para 0-10v igual para potenciometro
Pino 7 - AVI
Pino 8 - ACM
Pino 9 - 10v
These are files that came with mine. They work. Only issue I had with wiring is, I had to flip dir and pulse wire for it to run. Not total sure if it was me messing up in wiring at first or the print is wrong.
The second issue is this board will not support backlash offsets. Now looking for one that will. I've gotten as much as i could out of mechanically but need that last little bit.
http://www.rainman229.com