Leadshine

Page 1 of 6 1234 ... LastLast
Threads 1 to 20 of 113

Forum: Leadshine

Discuss Leadshine stepper/servo drives, motors, and controls here!

  1. ES-MH234120 As Spindle Motor

    Started by firepong‎, Yesterday 07:29 AM
    cnc, drive, motor, servo, spindle
    • Replies: 2
    • Views: 62
    Yesterday, 09:28 AM Go to last post
  2. Need Help!- MX4660 Input 5 not working

    Started by cduncan64‎, 09-17-2017 01:20 PM
    input, mx4660, pin, port, software
    • Replies: 1
    • Views: 286
    10-17-2018, 11:40 AM Go to last post
  3. Need Help!- HBS86H clone with Nema34 from act-motor

    Started by digdagdigedag‎, 02-19-2018 04:19 AM
    • Replies: 2
    • Views: 289
    10-17-2018, 03:44 AM Go to last post
  4. MX4660 Cooling Requirements?

    Started by canman77‎, 09-06-2018 10:10 AM
    diy, driver, enclosure, mx4660, power
    • Replies: 0
    • Views: 188
    09-06-2018, 10:10 AM Go to last post
  5. Need Help!- Leadshine servo driver tuning

    Started by Xienix‎, 07-27-2018 05:28 PM
    adjust, driver, leadshine, parameters, servo
    • Replies: 0
    • Views: 324
    07-27-2018, 05:28 PM Go to last post
    • Replies: 10
    • Views: 1,323
    07-03-2018, 10:45 AM Go to last post
  6. Need Help!- Leadshine MX4660 Power Supply Options

    Started by mrosso‎, 05-30-2018 11:36 PM
    • Replies: 6
    • Views: 368
    06-12-2018, 01:32 PM Go to last post
  7. Control software/hardware compatibility

    Started by makaplan‎, 06-04-2018 08:50 PM
    cnc, control, drivers, leadshine, software
    • Replies: 1
    • Views: 200
    06-05-2018, 01:04 AM Go to last post
  8. Newbie- Powering Leadshine MA860 driver with AC transformer

    Started by CNC_Amateur‎, 05-03-2018 04:17 AM
    capacitors, driver, ma860, powering, transformer
    • Replies: 2
    • Views: 337
    05-06-2018, 03:30 AM Go to last post
  9. Leadshine MX4660: How does a pair of digitial outputs work?

    Started by Tomboardman‎, 03-06-2017 09:06 PM
    3 Pages
    1 2 3
    • Replies: 27
    • Views: 1,634
    04-18-2018, 06:59 PM Go to last post
    • Replies: 8
    • Views: 1,415
    04-13-2018, 03:48 PM Go to last post
  10. Issues with Mach3 and M542T drivers

    Started by kodex‎, 03-15-2018 09:24 PM
    mach3, issue, issues, settings, experience
    • Replies: 5
    • Views: 311
    03-29-2018, 07:05 PM Go to last post
  11. Exclamation ES-DH2306 Tuning Issue

    Started by interzis‎, 02-24-2015 09:39 AM
    • Replies: 11
    • Views: 2,752
    03-25-2018, 04:47 PM Go to last post
  12. Need Help!- ProTuner Ver 1.3 communication problem with leadshine HBS1108S

    Started by Kadmos‎, 03-24-2018 11:10 PM
    • Replies: 0
    • Views: 277
    03-24-2018, 11:10 PM Go to last post
  13. New Machine Build- Four motors on a Leadshine MX3660

    Started by Trideciple‎, 02-22-2018 04:09 PM
    axis, cnc, motor, motors, mx3660
    • Replies: 1
    • Views: 371
    02-22-2018, 09:20 PM Go to last post
  14. CS-M vs ES-M - what is the difference

    Started by dixdance‎, 02-16-2018 02:52 PM
    closed, cs-m, difference, es-m, steppers
    • Replies: 2
    • Views: 222
    02-20-2018, 03:49 PM Go to last post
  15. Need Help!- Power Supply for HBS86H with Nema34

    Started by digdagdigedag‎, 02-18-2018 11:54 AM
    hbs86h, peak, power, side, transformer
    • Replies: 6
    • Views: 431
    02-19-2018, 03:46 AM Go to last post
  16. Leadshine D808 + ES-M22430 fault signal on mach3

    Started by jimskeet‎, 02-05-2018 12:11 PM
    • Replies: 1
    • Views: 337
    02-18-2018, 11:39 AM Go to last post
  17. Nema 34 cm series

    Started by drunkbilly‎, 02-14-2018 11:35 AM
    brands, consensus, general, leadshine, steppers
    • Replies: 1
    • Views: 171
    02-14-2018, 08:19 PM Go to last post
  18. Comments/thoughts on MX4660 wiring

    Started by ahacking‎, 12-13-2017 10:50 AM
    cnc, connected, endstop, gnd, stepper
    • Replies: 2
    • Views: 808
    01-06-2018, 05:10 PM Go to last post

Page 1 of 6 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands