Leadshine LD5-400 DC Servo Drive not working in jog run mode

Results 1 to 6 of 6

Thread: Leadshine LD5-400 DC Servo Drive not working in jog run mode

  1. #1
    ManjuHBR's Avatar
    Join Date
    Mar 2020
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Leadshine LD5-400 DC Servo Drive not working in jog run mode

    Hello sir,
    The Leadshine LD5-400 DC Servo Drive is not working in jog run mode. I m using the 3phase servo motor
    Motor Details:
    Voltage: 36v
    rpm: 3000rpm
    power: 200watt
    motor is with gear

    i connected uvw wires and encoder cable of motor to the ld5-400 drive and connected 36v power supply to driver.
    i tried running the motor but every time it gives the same error
    error1: 1A1 (which means com- is not connected)
    error1:100 (overload), but i have not connected any load. i have set all the parameters required for jog run mode in the user manual provided by leadshine. i tried running using protuner software but was not successful.
    please help me to solve this problem



  2. #2
    Member
    Join Date
    Nov 2013
    Posts
    4241
    Downloads
    0
    Uploads
    0

    Default Re: Leadshine LD5-400 DC Servo Drive not working in jog run mode

    Hi,
    you have connected the U,V,W wires, are they in a plug?. It may be that the servo is turning the wrong direction relative to the encoder.
    If that the case just swap any two of U,V.W.

    Craig



  3. #3
    ManjuHBR's Avatar
    Join Date
    Mar 2020
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: Leadshine LD5-400 DC Servo Drive not working in jog run mode

    Thanks for the suggestion Joeavaerage sir,
    U,V,W wires are not in a plug. I tried swapping the U,V,W wires but again the same error.



  4. #4
    Member
    Join Date
    Nov 2013
    Posts
    4241
    Downloads
    0
    Uploads
    0

    Default Re: Leadshine LD5-400 DC Servo Drive not working in jog run mode

    Hi,
    you should only swap two wires, say leave U where it is and swao the other two.

    Craig



  5. #5
    ManjuHBR's Avatar
    Join Date
    Mar 2020
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: Leadshine LD5-400 DC Servo Drive not working in jog run mode

    Hello sir,
    yes i did the same thing. i swapped the V,W wires. the error is 100(overload)



  6. #6
    Member
    Join Date
    Nov 2013
    Posts
    4241
    Downloads
    0
    Uploads
    0

    Default Re: Leadshine LD5-400 DC Servo Drive not working in jog run mode

    Hi,
    sorry I am not familiar enough with Leadshine servos to be of any help, I use Delta servos.

    Craig



  7. #7
    ManjuHBR's Avatar
    Join Date
    Mar 2020
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: Leadshine LD5-400 DC Servo Drive not working in jog run mode

    hello sir,
    it's ok thank you.



  8. #8
    Member
    Join Date
    May 2015
    Location
    China
    Posts
    38
    Downloads
    0
    Uploads
    0

    Default Re: Leadshine LD5-400 DC Servo Drive not working in jog run mode

    Hi ManjuHBR, thank you for supporting Leadshine products.
    The motor phase UVW must be corrected to the drive LD5, do you have motor datasheet and where did you buy the low voltage servo drive LD5-400?



Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Leadshine LD5-400 DC Servo Drive not working in jog run mode

Leadshine LD5-400 DC Servo Drive not working in jog run mode