Laser Hardware


Page 1 of 10 1234 ... LastLast
Threads 1 to 20 of 190

Forum: Laser Hardware

Sub-Forums Threads / Posts  Last Post

  1. Laser CO2 Tubes, Diodes, RF and Power Supplies here.

    Forum Actions:

    Forum Statistics:

    • Threads: 162
    • Posts: 764
  2. Discuss mirrors, beam expanders and other Optics here.

    Forum Actions:

    Forum Statistics:

    • Threads: 41
    • Posts: 142
  3. Laser Cooling

    (1 Viewing)

    Discuss chillers and other cooling methods.

    Forum Actions:

    Forum Statistics:

    • Threads: 17
    • Posts: 91
    • Replies: 3
    • Views: 520
    08-05-2020, 10:34 PM Go to last post
  1. RAYCUS RFL-P30Q/A3/115/2

    Started by Dwinget‎, 08-04-2020 01:29 PM
    laser, purchased.does, raycus, recently, rfl-p30q/a3/115/2
    • Replies: 0
    • Views: 78
    08-04-2020, 01:29 PM Go to last post
  2. Tube and power supply upgrade

    Started by andbad‎, 07-28-2020 12:47 PM
    output, power, supply, tube, voltage
    • Replies: 1
    • Views: 119
    07-29-2020, 11:45 AM Go to last post
  3. Replacement Controller

    Started by Legonerd‎, 03-17-2020 01:10 AM
    • Replies: 5
    • Views: 689
    07-01-2020, 09:52 PM Go to last post
  4. 40w laser tube lower voltage connector burn mark

    Started by NaN‎, 05-13-2020 07:17 AM
    • Replies: 0
    • Views: 406
    05-13-2020, 07:17 AM Go to last post
  5. Exclamation Melted wire from laser tube

    Started by Bryansglaser‎, 12-06-2019 04:13 AM
    • Replies: 10
    • Views: 1,040
    05-11-2020, 06:29 AM Go to last post
  6. Unhappy Help me. Mpc6515

    Started by ganxvv‎, 03-04-2020 08:18 AM
    • Replies: 0
    • Views: 291
    03-04-2020, 08:18 AM Go to last post
    • Replies: 1
    • Views: 525
    01-14-2020, 06:20 PM Go to last post
  7. CO2 Glass Laser Refill

    Started by KH0UJ‎, 05-15-2017 07:09 PM
    gas, laser, mixture, posts, tubes
    • Replies: 6
    • Views: 1,936
    12-09-2019, 10:09 AM Go to last post
  8. K40 chines Laser upgrade with an mksgen 1.4 board

    Started by vincentwelk‎, 12-07-2019 07:35 AM
    board, forum, k40 laser, mks gen, upgrade laser
    • Replies: 0
    • Views: 523
    12-07-2019, 07:35 AM Go to last post
    • Replies: 1
    • Views: 736
    11-13-2019, 04:16 PM Go to last post
  9. Bubble in laser tube

    Started by LesB‎, 11-03-2019 01:36 PM
    • Replies: 0
    • Views: 532
    11-03-2019, 01:36 PM Go to last post
    • Replies: 0
    • Views: 454
    10-28-2019, 10:53 PM Go to last post
  10. Laser power supply identification

    Started by danielex‎, 10-28-2019 06:51 AM
    • Replies: 0
    • Views: 586
    10-28-2019, 06:51 AM Go to last post
  11. Laser arcing on annode connection

    Started by pacguy‎, 10-09-2019 12:13 PM
    • Replies: 0
    • Views: 555
    10-09-2019, 12:13 PM Go to last post
    • Replies: 0
    • Views: 702
    09-04-2019, 07:23 AM Go to last post
  12. Newbie question about laser tubes

    Started by mordeckai‎, 08-01-2019 09:27 PM
    • Replies: 0
    • Views: 637
    08-01-2019, 09:27 PM Go to last post
    • Replies: 0
    • Views: 789
    07-20-2019, 02:43 AM Go to last post
  13. Exclamation LC1390N Setup Help

    Started by SamHatton‎, 07-15-2019 08:40 PM
    beam, g weike, good, gweike, laser
    • Replies: 0
    • Views: 617
    07-15-2019, 08:40 PM Go to last post

Page 1 of 10 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands