Laser Hardware

Page 1 of 8 1234 ... LastLast
Threads 1 to 20 of 155

Forum: Laser Hardware

Sub-Forums Threads / Posts  Last Post

  1. Laser CO2 Tubes, Diodes, RF and Power Supplies here.

    Forum Actions:

    Forum Statistics:

    • Threads: 126
    • Posts: 702
  2. Laser Optics

    (3 Viewing)

    Discuss mirrors, beam expanders and other Optics here.

    Forum Actions:

    Forum Statistics:

    • Threads: 37
    • Posts: 125
  3. Laser Cooling

    (3 Viewing)

    Discuss chillers and other cooling methods.

    Forum Actions:

    Forum Statistics:

    • Threads: 15
    • Posts: 74
  1. Laser Controller Cable Pin out RDC6442S(EC)

    Started by luckyboot44‎, 03-12-2018 12:24 PM
    connector, controller, display, pin, rdc6442sec
    • Replies: 2
    • Views: 293
    04-20-2018, 07:15 PM Go to last post
  2. Problems while playing a lasershow

    Started by kevinmanuel‎, 04-06-2018 04:31 AM
    • Replies: 1
    • Views: 57
    04-20-2018, 02:03 PM Go to last post
  3. Post NEED HELP! Chinese 60w Laser cutter won´t turn on.

    Started by arqmoe‎, 07-08-2016 09:10 AM
    • Replies: 6
    • Views: 743
    04-19-2018, 07:40 PM Go to last post
  4. Exclamation Please Help! Laser and optics question

    Started by ArtSigns‎, 04-19-2018 06:34 PM
    • Replies: 0
    • Views: 71
    04-19-2018, 06:34 PM Go to last post
  5. Exclamation Dangerous problem

    Started by joory_bh‎, 04-15-2018 03:22 AM
    filter, high voltage, power supply, tube
    • Replies: 0
    • Views: 121
    04-15-2018, 03:22 AM Go to last post
  6. where is there a more active diy laser forum?

    Started by keverett‎, 12-23-2017 02:23 PM
    active, diy, diyers, forum, laser
    • Replies: 7
    • Views: 672
    04-10-2018, 07:24 PM Go to last post
  7. Rotary unit for Thunder Laser 24

    Started by Alangdance‎, 04-10-2018 01:29 PM
    grateful, laser, rotary, thunder, unit
    • Replies: 0
    • Views: 59
    04-10-2018, 01:29 PM Go to last post
  8. HP Laser P3005H 49.4C18 error message

    Started by kevinmanuel‎, 04-06-2018 04:30 AM
    • Replies: 0
    • Views: 42
    04-06-2018, 04:30 AM Go to last post
  9. encoder control motor

    Started by lucasn73‎, 04-02-2018 07:07 AM
    • Replies: 0
    • Views: 91
    04-02-2018, 07:07 AM Go to last post
  10. Laser Does Not Home

    Started by ianthompson1982‎, 02-02-2018 04:48 PM
    • Replies: 4
    • Views: 192
    03-07-2018, 01:42 PM Go to last post
  11. Problem - Weird noises and movement

    Started by tobys123‎, 03-02-2018 04:34 AM
    movements, noises, problem, weird, wires
    • Replies: 5
    • Views: 280
    03-02-2018, 11:25 PM Go to last post
    • Replies: 0
    • Views: 98
    02-21-2018, 05:42 AM Go to last post
  12. Adding Laser to CNC

    Started by Nidalap‎, 02-14-2018 04:53 AM
    cnc, diode, forum, laser, software
    • Replies: 4
    • Views: 467
    02-19-2018, 03:03 AM Go to last post
  13. Power Supply for 80W laser

    Started by Chad Veich‎, 01-23-2018 02:46 PM
    find, machine, power, room, supply
    • Replies: 0
    • Views: 218
    01-23-2018, 02:46 PM Go to last post
    • Replies: 9
    • Views: 799
    01-06-2018, 06:03 PM Go to last post
  14. What laser controller to use?

    Started by enniobozzetti‎, 09-21-2017 06:11 AM
    controller, dsp, laser, mpc6525a, ruida
    • Replies: 4
    • Views: 579
    01-05-2018, 02:10 AM Go to last post
  15. question about Breakout board for Laser Cutter

    Started by keverett‎, 12-23-2017 09:28 PM
    breakout board, co2 laser cutting machine, cutter, diy laser engraver, laser cutter
    • Replies: 1
    • Views: 314
    12-27-2017, 10:24 AM Go to last post
  16. power supply adaptation for 90W Reci tube

    Started by keverett‎, 02-24-2017 10:46 PM
    laser, laser power supply, mismatched laser supply, power, supply
    • Replies: 1
    • Views: 302
    12-23-2017, 05:44 PM Go to last post
  17. Trotec Exhaust questions

    Started by tekjunkie28‎, 12-20-2017 08:04 AM
    blah, exhaust, prefilter, speedy, trotec
    • Replies: 0
    • Views: 185
    12-20-2017, 08:04 AM Go to last post
    • Replies: 1
    • Views: 204
    12-06-2017, 08:33 PM Go to last post

Page 1 of 8 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 17 users browsing this forum. (0 members & 17 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands