Laser CO2 Tubes, Diodes, RF and Power Supplies


Page 1 of 9 1234 ... LastLast
Threads 1 to 20 of 161

Forum: Laser CO2 Tubes, Diodes, RF and Power Supplies

Laser CO2 Tubes, Diodes, RF and Power Supplies here.

  1. Problem- Laser Arching

    Started by Rwallace5002‎, 03-10-2020 12:53 PM
    aching, back, laser, tube, white
    • Replies: 0
    • Views: 203
    03-10-2020, 12:53 PM Go to last post
  2. Laser module type rust paint removal

    Started by ratfink‎, 02-19-2020 07:32 PM
    held, laser, purchase, rust, type
    • Replies: 0
    • Views: 204
    02-19-2020, 07:32 PM Go to last post
  3. Need help with PWM laser control in Mach3

    Started by garymiller397‎, 01-03-2020 03:06 PM
    • Replies: 3
    • Views: 346
    01-28-2020, 03:25 AM Go to last post
  4. Question Need Help!- new tube install problem

    Started by gventer‎, 01-27-2020 07:03 PM
    bought, coming, install, reduce, tube
    • Replies: 0
    • Views: 168
    01-27-2020, 07:03 PM Go to last post
  5. HV Desk Error - Bystar 3015 (2002)

    Started by moleda‎, 01-16-2020 11:11 AM
    bystar, bystronic, hv desk error
    • Replies: 0
    • Views: 175
    01-16-2020, 11:11 AM Go to last post
  6. Need Help!- Needing to refill my laser tube

    Started by Carlosgomezji‎, 01-08-2020 09:43 PM
    deos, laser, laser tube refill, reliable, tube
    • Replies: 0
    • Views: 323
    01-08-2020, 09:43 PM Go to last post
  7. Controller or power supply temperature limits?

    Started by bcheary‎, 01-02-2020 09:24 PM
    controller, great, machine, ruida rdc6442 control, temperatures
    • Replies: 0
    • Views: 173
    01-02-2020, 09:24 PM Go to last post
  8. Power supply input voltage conversion

    Started by VnillaThund3r‎, 12-29-2019 05:57 PM
    cnc, i’m, laser, power, supply
    • Replies: 1
    • Views: 305
    12-29-2019, 08:12 PM Go to last post
  9. Laser removal????

    Started by jaysteel‎, 12-24-2019 08:09 AM
    back, laser, machine, unbolt, unplug
    • Replies: 0
    • Views: 294
    12-24-2019, 08:09 AM Go to last post
  10. Need Help!- Reci 100watt Laser Beam is Ring Shaped

    Started by Eleusis‎, 12-07-2019 06:21 AM
    • Replies: 0
    • Views: 396
    12-07-2019, 06:21 AM Go to last post
  11. material sensor (amplifier) for Trocen TF-6225

    Started by tloudev‎, 12-05-2019 05:03 AM
    amplifier, problem, sensor, tf-6225, trocen
    • Replies: 0
    • Views: 220
    12-05-2019, 05:03 AM Go to last post
  12. Choosing Co2 tube for DIY laser

    Started by kapel‎, 09-30-2019 05:26 AM
    • Replies: 1
    • Views: 660
    11-24-2019, 08:07 AM Go to last post
  13. Co2 laser power supply ( HV ) with low current

    Started by oneeye‎, 11-09-2019 09:20 AM
    40kv, current, laser, make, psu
    • Replies: 0
    • Views: 425
    11-09-2019, 09:20 AM Go to last post
    • Replies: 1
    • Views: 2,068
    11-07-2019, 01:02 PM Go to last post
  14. Problem - Power dropping as laser power level goes up

    Started by studio-N‎, 08-15-2019 07:40 AM
    laser, output, power, reci, supply
    • Replies: 2
    • Views: 496
    08-24-2019, 08:57 AM Go to last post
  15. Problem- Problem with co2 power supply sound

    Started by NeODarK‎, 08-07-2019 06:11 AM
    co2, noise, power, supply, tube
    • Replies: 3
    • Views: 626
    08-19-2019, 10:36 AM Go to last post
    • Replies: 0
    • Views: 319
    08-13-2019, 02:18 PM Go to last post
  16. Problem- Laser Power varies

    Started by dakimber‎, 05-21-2019 12:09 AM
    current, cut, laser, power, power loss
    • Replies: 0
    • Views: 529
    05-21-2019, 12:09 AM Go to last post
  17. High power wire splice and extension

    Started by chuck767‎, 03-12-2019 11:59 PM
    high, power, splice, type, wire
    • Replies: 1
    • Views: 567
    03-13-2019, 10:11 AM Go to last post
  18. Need Help!- Low laser current means time to replace the tube?

    Started by makerstoolworks‎, 01-09-2019 02:21 AM
    laser, output, power, supply, tube
    • Replies: 1
    • Views: 674
    02-19-2019, 08:00 PM Go to last post

Page 1 of 9 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 6 users browsing this forum. (0 members & 6 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands