Laser CO2 Tubes, Diodes, RF and Power Supplies


Page 1 of 8 1234 ... LastLast
Threads 1 to 20 of 152

Forum: Laser CO2 Tubes, Diodes, RF and Power Supplies

Laser CO2 Tubes, Diodes, RF and Power Supplies here.

  1. Need Help!- Reci 100watt Laser Beam is Ring Shaped

    Started by Eleusis‎, Today 07:21 AM
    • Replies: 0
    • Views: 33
    Today, 07:21 AM Go to last post
  2. material sensor (amplifier) for Trocen TF-6225

    Started by tloudev‎, 12-05-2019 06:03 AM
    amplifier, problem, sensor, tf-6225, trocen
    • Replies: 0
    • Views: 63
    12-05-2019, 06:03 AM Go to last post
  3. Choosing Co2 tube for DIY laser

    Started by kapel‎, 09-30-2019 06:26 AM
    • Replies: 1
    • Views: 338
    11-24-2019, 09:07 AM Go to last post
  4. Co2 laser power supply ( HV ) with low current

    Started by oneeye‎, 11-09-2019 10:20 AM
    40kv, current, laser, make, psu
    • Replies: 0
    • Views: 137
    11-09-2019, 10:20 AM Go to last post
    • Replies: 1
    • Views: 1,865
    11-07-2019, 02:02 PM Go to last post
  5. Problem - Power dropping as laser power level goes up

    Started by studio-N‎, 08-15-2019 08:40 AM
    laser, output, power, reci, supply
    • Replies: 2
    • Views: 288
    08-24-2019, 09:57 AM Go to last post
  6. Problem- Problem with co2 power supply sound

    Started by NeODarK‎, 08-07-2019 07:11 AM
    co2, noise, power, supply, tube
    • Replies: 3
    • Views: 343
    08-19-2019, 11:36 AM Go to last post
    • Replies: 0
    • Views: 156
    08-13-2019, 03:18 PM Go to last post
  7. Problem- Laser Power varies

    Started by dakimber‎, 05-21-2019 01:09 AM
    current, cut, laser, power, power loss
    • Replies: 0
    • Views: 306
    05-21-2019, 01:09 AM Go to last post
  8. High power wire splice and extension

    Started by chuck767‎, 03-13-2019 12:59 AM
    high, power, splice, type, wire
    • Replies: 1
    • Views: 289
    03-13-2019, 11:11 AM Go to last post
  9. Need Help!- Low laser current means time to replace the tube?

    Started by makerstoolworks‎, 01-09-2019 03:21 AM
    laser, output, power, supply, tube
    • Replies: 1
    • Views: 424
    02-19-2019, 09:00 PM Go to last post
  10. reci p18 power supply trouble, not enough current

    Started by arachid‎, 02-05-2019 11:43 AM
    3.4v, current, descrease, reci, start
    • Replies: 0
    • Views: 271
    02-05-2019, 11:43 AM Go to last post
  11. rf tube hose

    Started by mrsa‎, 01-25-2019 10:20 AM
    hose, tube
    • Replies: 0
    • Views: 255
    01-25-2019, 10:20 AM Go to last post
  12. Need Help!- lookiing for a RECI rep

    Started by cnctoolman‎, 01-22-2019 12:00 PM
    anymore, board, intouch, reci, reps
    • Replies: 0
    • Views: 264
    01-22-2019, 12:00 PM Go to last post
  13. LaserCad

    Started by tmcduffee‎, 01-10-2019 12:07 PM
    • Replies: 0
    • Views: 184
    01-10-2019, 12:07 PM Go to last post
  14. Question Program stops responding

    Started by KGV‎, 01-06-2019 01:09 PM
    • Replies: 0
    • Views: 203
    01-06-2019, 01:09 PM Go to last post
  15. Newbie- Do laser tubes degrade in storage?

    Started by ZeptoBit‎, 09-29-2018 08:59 AM
    buying, laser, spare, tube, tubes
    • Replies: 2
    • Views: 568
    10-23-2018, 04:20 AM Go to last post
    • Replies: 0
    • Views: 316
    10-04-2018, 01:34 PM Go to last post
  16. Help with Coherent C Series laser

    Started by vova‎, 09-30-2018 04:18 AM
    • Replies: 0
    • Views: 383
    09-30-2018, 04:18 AM Go to last post
  17. Which Tube Brand?

    Started by neo__04‎, 08-06-2018 09:55 AM
    aiming, brand, consensus, tube, worth
    • Replies: 2
    • Views: 557
    08-22-2018, 12:32 PM Go to last post

Page 1 of 8 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 15 users browsing this forum. (0 members & 15 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands