Laser CO2 Tubes, Diodes, RF and Power Supplies


Page 1 of 8 1234 ... LastLast
Threads 1 to 20 of 148

Forum: Laser CO2 Tubes, Diodes, RF and Power Supplies

Laser CO2 Tubes, Diodes, RF and Power Supplies here.

  1. Problem - Power dropping as laser power level goes up

    Started by studio-N‎, 08-15-2019 07:40 AM
    laser, output, power, reci, supply
    • Replies: 2
    • Views: 209
    08-24-2019, 08:57 AM Go to last post
  2. Problem- Problem with co2 power supply sound

    Started by NeODarK‎, 08-07-2019 06:11 AM
    co2, noise, power, supply, tube
    • Replies: 3
    • Views: 242
    08-19-2019, 10:36 AM Go to last post
    • Replies: 0
    • Views: 106
    08-13-2019, 02:18 PM Go to last post
  3. Problem- Laser Power varies

    Started by dakimber‎, 05-21-2019 12:09 AM
    current, cut, laser, power, power loss
    • Replies: 0
    • Views: 229
    05-21-2019, 12:09 AM Go to last post
  4. High power wire splice and extension

    Started by chuck767‎, 03-12-2019 11:59 PM
    high, power, splice, type, wire
    • Replies: 1
    • Views: 204
    03-13-2019, 10:11 AM Go to last post
  5. Need Help!- Low laser current means time to replace the tube?

    Started by makerstoolworks‎, 01-09-2019 02:21 AM
    laser, output, power, supply, tube
    • Replies: 1
    • Views: 325
    02-19-2019, 08:00 PM Go to last post
  6. reci p18 power supply trouble, not enough current

    Started by arachid‎, 02-05-2019 10:43 AM
    3.4v, current, descrease, reci, start
    • Replies: 0
    • Views: 206
    02-05-2019, 10:43 AM Go to last post
  7. rf tube hose

    Started by mrsa‎, 01-25-2019 09:20 AM
    hose, tube
    • Replies: 0
    • Views: 189
    01-25-2019, 09:20 AM Go to last post
  8. Need Help!- lookiing for a RECI rep

    Started by cnctoolman‎, 01-22-2019 11:00 AM
    anymore, board, intouch, reci, reps
    • Replies: 0
    • Views: 206
    01-22-2019, 11:00 AM Go to last post
  9. LaserCad

    Started by tmcduffee‎, 01-10-2019 11:07 AM
    • Replies: 0
    • Views: 138
    01-10-2019, 11:07 AM Go to last post
  10. Question Program stops responding

    Started by KGV‎, 01-06-2019 12:09 PM
    • Replies: 0
    • Views: 151
    01-06-2019, 12:09 PM Go to last post
  11. Newbie- Do laser tubes degrade in storage?

    Started by ZeptoBit‎, 09-29-2018 07:59 AM
    buying, laser, spare, tube, tubes
    • Replies: 2
    • Views: 458
    10-23-2018, 03:20 AM Go to last post
    • Replies: 0
    • Views: 245
    10-04-2018, 12:34 PM Go to last post
  12. Help with Coherent C Series laser

    Started by vova‎, 09-30-2018 03:18 AM
    • Replies: 0
    • Views: 307
    09-30-2018, 03:18 AM Go to last post
  13. Which Tube Brand?

    Started by neo__04‎, 08-06-2018 08:55 AM
    aiming, brand, consensus, tube, worth
    • Replies: 2
    • Views: 480
    08-22-2018, 11:32 AM Go to last post
  14. Build Thread- SPT-TR150 Visible co2 Laser tube

    Started by CeeLtd‎, 07-09-2018 02:35 PM
    • Replies: 2
    • Views: 506
    08-08-2018, 09:42 AM Go to last post
  15. Need Help!- Co2 upgrading: laser supply selection HELP! [2nd section]

    Started by ramonv35‎, 07-27-2018 07:27 PM
    • Replies: 1
    • Views: 372
    08-06-2018, 04:04 PM Go to last post
  16. Need Help!- 60W power supply - Correct amperage?

    Started by rjd1234‎, 07-05-2018 07:56 PM
    60w, co2, laser, power, supply
    • Replies: 0
    • Views: 333
    07-05-2018, 07:56 PM Go to last post
  17. Power supply bigger than suited for tube?

    Started by neo__04‎, 04-29-2018 05:04 AM
    40w, bigger, buy, power, tube
    • Replies: 2
    • Views: 787
    06-26-2018, 11:50 PM Go to last post
  18. Exclamation Need Help!- Wiring between controller and PS

    Started by rolandver‎, 06-24-2018 07:46 AM
    • Replies: 1
    • Views: 337
    06-24-2018, 09:45 AM Go to last post

Page 1 of 8 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands