Laser CO2 Tubes, Diodes, RF and Power Supplies


Page 1 of 9 1234 ... LastLast
Threads 1 to 20 of 173

Forum: Laser CO2 Tubes, Diodes, RF and Power Supplies

Laser CO2 Tubes, Diodes, RF and Power Supplies here.

  1. Need Help!- Laser beam wobble

    Started by mcdonald79‎, 10-22-2021 01:58 PM
    • Replies: 1
    • Views: 106
    10-22-2021, 03:18 PM Go to last post
    • Replies: 0
    • Views: 61
    10-22-2021, 01:10 PM Go to last post
  2. diy CO2 laser tube

    Started by AndreiBogdan‎, 01-04-2021 12:04 PM
    • Replies: 1
    • Views: 747
    10-15-2021, 10:51 AM Go to last post
  3. Newbie- Laser Tube Size Clarification

    Started by rlrcstr‎, 05-12-2021 05:57 PM
    hours, laser, lifetime, price, tube
    • Replies: 1
    • Views: 840
    05-13-2021, 10:54 AM Go to last post
    • Replies: 0
    • Views: 3,629
    04-26-2021, 06:17 PM Go to last post
  4. Synrad 48 tube with a Trocen AWC708 plus?

    Started by drumsticksplint‎, 03-03-2021 10:28 AM
    • Replies: 1
    • Views: 2,674
    03-24-2021, 09:56 AM Go to last post
  5. Co2 laser tube producer outside chin

    Started by Reidarr‎, 12-24-2020 05:45 PM
    • Replies: 1
    • Views: 1,032
    12-24-2020, 08:40 PM Go to last post
    • Replies: 0
    • Views: 1,059
    12-21-2020, 09:27 PM Go to last post
  6. Need Help!- Laser power suddenly reduced

    Started by Mechanikum‎, 10-16-2020 11:47 AM
    • Replies: 1
    • Views: 1,043
    10-17-2020, 06:41 AM Go to last post
  7. Does this look like a good 80w RICI firing? (video)

    Started by 34ford‎, 09-11-2020 12:37 PM
    80w, bad, firing, good, rici
    • Replies: 0
    • Views: 933
    09-11-2020, 12:37 PM Go to last post
  8. 40w to 80w wiring question (FSL MUSE)

    Started by Cwcustomworx‎, 08-24-2020 06:33 AM
    • Replies: 1
    • Views: 875
    08-24-2020, 08:21 AM Go to last post
  9. Angry Need Help!- Laser suddenly won't fire - tube or power supply?

    Started by jbarber‎, 05-20-2016 01:08 PM
    fine, power, quit, supply, tube
    • Replies: 11
    • Views: 2,551
    08-15-2020, 10:41 PM Go to last post
  10. Laser Power

    Started by salem,oregon‎, 11-08-2014 07:38 PM
    • Replies: 4
    • Views: 1,883
    07-30-2020, 04:04 AM Go to last post
  11. 130w tube arching at both ends.

    Started by mark.a‎, 07-14-2020 08:20 AM
    beam, fired, laser, tube, water
    • Replies: 1
    • Views: 878
    07-14-2020, 04:23 PM Go to last post
  12. Need Help!- Reci 100watt Laser Beam is Ring Shaped

    Started by Eleusis‎, 12-07-2019 06:21 AM
    • Replies: 1
    • Views: 1,631
    06-28-2020, 10:01 AM Go to last post
  13. Unhappy Laser tube supplier for Europe... with warranty?

    Started by gillespinault‎, 02-20-2013 06:33 AM
    co2 laser tube, down, laser tube broken, then
    • Replies: 14
    • Views: 8,244
    05-11-2020, 02:40 PM Go to last post
  14. Laser module type rust paint removal

    Started by ratfink‎, 02-19-2020 07:32 PM
    • Replies: 3
    • Views: 1,316
    04-16-2020, 05:27 PM Go to last post
  15. Problem- Laser Arching

    Started by Rwallace5002‎, 03-10-2020 12:53 PM
    aching, back, laser, tube, white
    • Replies: 0
    • Views: 722
    03-10-2020, 12:53 PM Go to last post
  16. Need help with PWM laser control in Mach3

    Started by garymiller397‎, 01-03-2020 03:06 PM
    • Replies: 3
    • Views: 2,259
    01-28-2020, 03:25 AM Go to last post
  17. Question Need Help!- new tube install problem

    Started by gventer‎, 01-27-2020 07:03 PM
    bought, coming, install, reduce, tube
    • Replies: 0
    • Views: 588
    01-27-2020, 07:03 PM Go to last post

Page 1 of 9 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 3 users browsing this forum. (0 members & 3 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands