I can recommend lightobjects.com. Marco, the owner is very friendly and service minded.
We bought a RECI w6 tube that worked for 10 minuts before the arc penetatred the inner tube. We had a replacement within a week.
Hi,
I have had two 80w CO2 laser tube broken in less then three monthes
The first time I was using a simple aquarium pump in a large bucket I didn't know I had to care too much for air bubbles so probably air bubble caused the tube to explode...
So we replaced the tube, we bough a CW3000 chiller and were super careful about air bubbles, but after just a few hours of use, power suddenly dropped down and we could find a crack in the laser tube! I am sure their were no air bubbles and the temperature stated by the cooler was 19°C.
Do I have a problem with my laser tube provider?
Do you think I should have my whole installation checked? Does anyone have clues on who could do that in Belgium (Brussels)?
Can you advise me with a reliable laser tube provider, preferably with a warranty?
Any information will be much appreciated!
Similar Threads:
I can recommend lightobjects.com. Marco, the owner is very friendly and service minded.
We bought a RECI w6 tube that worked for 10 minuts before the arc penetatred the inner tube. We had a replacement within a week.
Hi Gillespinault,
We can provide Reci laser tube with packing , and any problems of this tube which should be in it's warranty .
If you are intreseted ,hope we can share a good cooperation from now .
Best regards,
XYZ Machinery
Thank you for the link Guldberg, unfortunatly, lightobject seems to be based in california, shipping to europe is most likely very expensive.
Thank you Exalaser, can you provide me with a quote for a RECI laser tube suitable to replace my 80w laser, including shipping to Belgium?
Hi gillespinault
You better do not believe in EXLASer`s offers.
Two years ago we bought laser machine with Reci from this factory.
After long time hard work we decided to scrap it.
As we are resellers this "product" was unfitted for anything else.
We did not get any help from seller (EXLASer).
Regards
Last edited by cinematic2; 03-26-2013 at 03:16 AM.
CNC lasers, constructions, service
(EXLASer) Have Good Products and the after sales department is a good one too.
I have purchased a year ago an Exlas 90/60 80watts and it works very good for me.
ah ok he just put the wrong url, thanks
http://www.cnczone.com/forums/laser_...ml#post1243846
Hi - I'm looking fir supplies to put a CO2 laser on my router. Any leads for tubes, power source etc to do this? I'm in Australia. Peter
I am doing business in CO2 laser, very glad to provide relevant help. Email: olivknightuk@gmail.com. Thanks
I am doing business in CO2 laser, very glad to provide relevant help. Email: olivknightuk@gmail.com. Thanks
Hey TIE, do you have a site?
Hate posts with "Trust me I know what I'm doing, I'm an Engineer"
BTW, I am selling canned fog as well as bottled Snake Oil
Make no mistake between my personality and my attitude.
My personality is who I am. My attitude depends on who you are.
Don't get fooled, the CW3000 is NOT a chiller. It is a fake one because there is no AC compressor. If you use it to drive a 80W tube in a garage, the water temperature will rise up to 50'C in 10~15min!!
Wost enough that the temperature pro does not really 'touch' water direct but through an insulation, so if you read, say 30'C, the actual temperature could be as high as 35'C or higher.
Stay away the CW3000. It is good for 40W or lower tube or if you location with room temperature is cold enough, say 20'C or lower!
We reject to sell a laser tube without signing a wavie form to accept less warranty period. For a100W, we will drop the warranty from 1yr to 3months only. We found that CW3000 could cause a lot issue. It may not kill the tube instantly but it will 1) shorter the life span 2) lower cutting perfomance.
-M
Hello,
If you need any help or advise regarding your Co2 laser machines we would be more than happy to help. We offer Co2 lasers machine and parts sales as well as offering maintenance agreements, tech support, parts installation with warranty, maintenance agreements and much more to ensure your machines get back up and running as soon as possible.
Please do visit our website at Laser Cutter | Laser Engraver | Laser Machine Parts & Accessories | CO2 Laser Machines | CO2 Laser Repairs | CO2 Laser Engineer or email info@focusedlasersystems.com for more information.
Kind regards,
Jake Osman
Focused Laser Systems Ltd