Mycenter 3 with Yasnac i80 data needed


Results 1 to 8 of 8

Thread: Mycenter 3 with Yasnac i80 data needed

  1. #1
    Registered
    Join Date
    Jul 2007
    Location
    Vietnam
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default Mycenter 3 with Yasnac i80 data needed

    Hello all,
    We are looking for the data and parameter of the Kitamura Mycenter 3 machine with Yasnac i80 controller. We are willing to pay for that.
    Thanks in advance.

    Similar Threads:


  2. #2
    Registered
    Join Date
    Jan 2015
    Posts
    5
    Downloads
    0
    Uploads
    0

    Default Re: Mycenter 3 with Yasnac i80 data needed

    еще актуально ? у меня есть на работе такой станок и параметры к нему



  3. #3
    Registered
    Join Date
    Jan 2015
    Posts
    42
    Downloads
    0
    Uploads
    0

    Default Re: Mycenter 3 with Yasnac i80 data needed

    What do you need? Parameters?
    Email me at : simplersys@gmail.com



  4. #4
    Registered
    Join Date
    Jul 2007
    Location
    Vietnam
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default Re: Mycenter 3 with Yasnac i80 data needed

    Thanks Kostikost and Ncbobbys for your reply.
    I already sent an email to Ncbobbys.



  5. #5
    Registered
    Join Date
    Jul 2007
    Location
    Vietnam
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default Re: Mycenter 3 with Yasnac i80 data needed

    Thanks Ncbobbys for your helps. We're appreciated that.



  6. #6
    Registered
    Join Date
    Aug 2009
    Location
    India
    Posts
    10
    Downloads
    0
    Uploads
    0

    Default Re: Mycenter 3 with Yasnac i80 data needed

    I purchased a used KITAMURA MYCENTER 3X machine with YASNAC i80M controller. This is our first CNC machine in our conventional machine shop. But the machine came to us in dead condition. As we don't know much about CNC machine's we purchased the machine. Now its lying with us for 4 years without any use. Now we want to run the machine, we approached a CNC machine service person, he switched ON the machine and said that the MEMORY of the machine is LOST due to bad memory battery. He told that he need the machine parameters and OPTION parameters to input.

    So please send me the Parameters, OPTION parameters and tool change macro programs also (if u have) for the machine immediately, PLEASE PLEASE do the needful immediately.

    THE MACHINE MODEL is : KITAMURA MYCENTER 3X with 3 axis and 1 spindle the axis drive models are CACR IR10SB (2 Nos.) for X and Y axis and CACR IR30SB for Z axis and VARISPEED spindle drive unit.

    PLEASE try to help me to commission the machine by sending the OPTION PARAMETS, MACHINE PARAMETERS and MACRO PROGRAMS.

    Thanking you in advance.

    Regards
    Vinothkumar R



  7. #7
    Registered
    Join Date
    Aug 2009
    Location
    India
    Posts
    10
    Downloads
    0
    Uploads
    0

    Default Re: Mycenter 3 with Yasnac i80 data needed

    I purchased a used KITAMURA MYCENTER 3X machine with YASNAC i80M controller. This is our first CNC machine in our conventional machine shop. But the machine came to us in dead condition. As we don't know much about CNC machine's we purchased the machine. Now its lying with us for 4 years without any use. Now we want to run the machine, we approached a CNC machine service person, he switched ON the machine and said that the MEMORY of the machine is LOST due to bad memory battery. He told that he need the machine parameters and OPTION parameters to input.

    So please send me the Parameters, OPTION parameters and tool change macro programs also (if u have) for the machine immediately, PLEASE PLEASE do the needful immediately.

    THE MACHINE MODEL is : KITAMURA MYCENTER 3X with 3 axis and 1 spindle the axis drive models are CACR IR10SB (2 Nos.) for X and Y axis and CACR IR30SB for Z axis and VARISPEED spindle drive unit.

    PLEASE try to help me to commission the machine by sending the OPTION PARAMETS, MACHINE PARAMETERS and MACRO PROGRAMS.

    my email ID is : vnotkmr@gmail.com

    Thanking you in advance.

    Regards
    Vinothkumar R



  8. #8
    Member
    Join Date
    Jun 2019
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    Hello. Please help with the parameters and startup programs on Kitamura H250 4-x. Thank.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Mycenter 3 with Yasnac i80 data needed

Mycenter 3 with Yasnac i80 data needed