K2CNC


Page 1 of 8 1234 ... LastLast
Threads 1 to 20 of 155

Forum: K2CNC

Discuss K2cnc machines here!

  1. Question Need Help!- KT-2514 Mach 3 settings

    Started by 2_jammer‎, 09-14-2010 09:44 PM
    then
    • Replies: 1
    • Views: 1,946
    09-20-2010, 10:14 PM Go to last post
  2. What are your rapid speeds?

    Started by 2_jammer‎, 09-09-2012 02:35 PM
    everyone
    • Replies: 4
    • Views: 2,173
    10-09-2012, 08:18 AM Go to last post
  3. X-axis leadscrew squeaking and tight

    Started by Alex Watson‎, 04-07-2007 06:21 PM
    kg3925, lumpy
    • Replies: 2
    • Views: 3,232
    05-07-2007, 08:12 PM Go to last post
  4. Thought on K2 25 X 25

    Started by amowry‎, 03-11-2013 11:19 PM
    • Replies: 1
    • Views: 1,968
    04-15-2013, 07:18 PM Go to last post
  5. Arrow Problem- Review on the KT1414

    Started by Anubisbot‎, 05-11-2008 04:56 PM
    almost, already, another, behind, cause, down, its, not, say, since, went
    • Replies: 4
    • Views: 3,792
    05-23-2008, 11:36 AM Go to last post
  6. Need Help!- Questions about K2CNC

    Started by Austin R‎, 12-02-2012 06:30 PM
    • Replies: 1
    • Views: 2,103
    12-13-2012, 09:44 AM Go to last post
  7. Slide bearings

    Started by a_johnson‎, 11-15-2011 10:37 AM
    • Replies: 2
    • Views: 2,037
    11-16-2011, 10:33 AM Go to last post
  8. Problem- X-axis fault light coming on

    Started by B.Wolfe‎, 07-07-2011 06:22 PM
    cause, then, went
    • Replies: 2
    • Views: 1,722
    07-13-2011, 10:32 AM Go to last post
  9. Need Help!- Troubleshooting

    Started by BFHammer‎, 11-19-2018 02:33 PM
    k2cnc, mach 3, motion, power, replaced
    • Replies: 4
    • Views: 4,138
    11-26-2018, 12:42 PM Go to last post
  10. Need Help!- K2cnc BOB

    Started by BIRDTOOL‎, 01-31-2013 02:22 PM
    • Replies: 0
    • Views: 1,706
    01-31-2013, 02:22 PM Go to last post
  11. rack and pinion rough

    Started by bo whipkey‎, 03-18-2010 08:22 PM
    almost, down, not
    • Replies: 2
    • Views: 2,099
    04-27-2011, 02:05 AM Go to last post
  12. Problem- not getting the green light ?

    Started by bootleg‎, 02-27-2016 07:59 AM
    green, k2cnc, light, reset, software
    • Replies: 1
    • Views: 1,802
    03-04-2016, 09:47 PM Go to last post
  13. K2 CNC distance problems

    Started by bootleg‎, 04-24-2016 09:00 AM
    cnc, computer, k2 cnc, ruler, software
    • Replies: 5
    • Views: 2,375
    04-24-2016, 04:30 PM Go to last post
  14. Won't enable

    Started by BRAIL‎, 01-16-2017 11:24 AM
    errors, issue, machine, power, receiving
    • Replies: 6
    • Views: 3,400
    01-17-2017, 09:11 AM Go to last post
  15. Need Help!- K2CNC 2525 not responding to Mach3

    Started by carpenterscnc‎, 03-13-2015 01:26 PM
    communicating, help - new to this, k2cnc, mach3, support
    • Replies: 0
    • Views: 1,321
    03-13-2015, 01:26 PM Go to last post
  16. Matercam Post processor

    Started by casta-baga‎, 11-26-2009 11:28 AM
    • Replies: 1
    • Views: 1,777
    12-16-2009, 07:14 AM Go to last post
  17. K2 3925 help needed. Losing Z axis height?

    Started by cerk‎, 05-27-2012 06:01 AM
    everyone
    • Replies: 3
    • Views: 2,614
    12-11-2013, 11:39 AM Go to last post
  18. K2 prototype thread

    Started by cgallery‎, 07-30-2008 12:24 PM
    6207
    • Replies: 1
    • Views: 2,321
    08-01-2008, 09:48 AM Go to last post
  19. Slightly eliptical circles

    Started by cgallery‎, 03-14-2017 11:30 AM
    cnc, final, machine, slightly, wondering
    • Replies: 7
    • Views: 3,123
    03-14-2017, 07:50 PM Go to last post
  20. Looking for a Used K2

    Started by CHagest‎, 10-26-2009 07:19 PM
    • Replies: 0
    • Views: 1,778
    10-26-2009, 07:19 PM Go to last post

Page 1 of 8 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 12 users browsing this forum. (0 members & 12 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands