Hyundai Kia

Page 1 of 15 123411 ... LastLast
Threads 1 to 20 of 296

Forum: Hyundai Kia

Discuss Hyundai Kia machines here.

  1. M code for chip conveyor and flushing coolant?

    Started by J S Machine‎, 06-18-2020 01:59 PM
    chip, code, conveyor, coolant, flushing
    • Replies: 1
    • Views: 307
    07-21-2020, 08:18 AM Go to last post
  2. Hyundai Kia SKT 200 Alarms

    Started by RubenCarner‎, 05-28-2020 04:17 AM
    • Replies: 1
    • Views: 224
    07-16-2020, 04:19 AM Go to last post
  3. Turret encoder only counts even number stations

    Started by senna95‎, 07-10-2020 01:08 PM
    encoder, hyundai, station, turret
    • Replies: 6
    • Views: 187
    07-14-2020, 08:09 AM Go to last post
  4. Need Help!- Mastercam 2018 post for Hyundai 15s 840c controller

    Started by tward74‎, 06-25-2020 04:33 AM
    15s, 840c, controller, hyundai, mastercam
    • Replies: 0
    • Views: 257
    06-25-2020, 04:33 AM Go to last post
  5. hyundai turning center problems

    Started by bbblackhills‎, 05-14-2020 09:55 AM
    center, control, error, hyundai, turning
    • Replies: 0
    • Views: 347
    05-14-2020, 09:55 AM Go to last post
  6. Hyundai HiT-18s Siemens hard drive replacement

    Started by svtford4x4‎, 11-03-2014 11:50 AM
    • Replies: 3
    • Views: 3,133
    03-29-2020, 12:14 AM Go to last post
  7. hit 15s manual (840c)

    Started by jonrya91‎, 03-21-2020 09:26 PM
    diagnose, helpful, machine, manual, wiring
    • Replies: 3
    • Views: 468
    03-24-2020, 03:30 AM Go to last post
  8. Parameters Hyundai Hit-15F

    Started by jgodwin16‎, 03-14-2020 10:45 PM
    • Replies: 2
    • Views: 320
    03-15-2020, 01:33 PM Go to last post
  9. Need Help!- Dangerous run a way X axis servo Kia Turn 21

    Started by shad061‎, 02-21-2020 02:44 AM
    alarm, circuit, issue, limit, switch
    • Replies: 0
    • Views: 522
    02-21-2020, 02:44 AM Go to last post
  10. Hit250m mr-j2s-100a-s046 turret servo drive

    Started by seraum‎, 01-24-2020 01:01 PM
    • Replies: 0
    • Views: 367
    01-24-2020, 01:01 PM Go to last post
  11. Post Need Help!- KIA 21LMS w Mitsubishi 520L control - Manuals Needed

    Started by vpcnc‎, 10-23-2019 11:13 AM
    kia, kia 21lms, manuals, mit 520l
    • Replies: 0
    • Views: 800
    10-23-2019, 11:13 AM Go to last post
  12. HiT 15s Spindle won't go over 70 rpm

    Started by jonrya91‎, 09-18-2019 07:09 AM
    • Replies: 3
    • Views: 839
    09-29-2019, 04:43 PM Go to last post
  13. Need Help!- Loading Hyundai Hit 20 parameters

    Started by taxslave‎, 09-03-2019 10:11 PM
    • Replies: 5
    • Views: 783
    09-26-2019, 02:05 PM Go to last post
  14. Need Help. Stuck in MDI mode.

    Started by 308billw‎, 09-10-2019 03:03 PM
    • Replies: 0
    • Views: 564
    09-10-2019, 03:03 PM Go to last post
  15. AL-4 Lubrication Oil Lack alarm

    Started by John-INTENSE‎, 05-20-2019 05:45 PM
    alarm, fluid, hydraulic, lubricant, specs
    • Replies: 3
    • Views: 827
    09-03-2019, 10:00 PM Go to last post
  16. STK 460

    Started by Dylan1985‎, 08-12-2019 07:58 PM
    aligned, it’s, moves, pressure, suggestions
    • Replies: 0
    • Views: 681
    08-12-2019, 07:58 PM Go to last post
  17. vx400 tool changer recovery

    Started by lakey0‎, 08-06-2019 10:55 AM
    change, cycle, recovery, rotated, tool
    • Replies: 1
    • Views: 598
    08-06-2019, 02:47 PM Go to last post
  18. Unhappy Need Help!- Turret Issue after Battery Dead Al-62 SKT21 LMS built 2010

    Started by HNiekamp‎, 07-19-2019 04:53 AM
    • Replies: 5
    • Views: 961
    07-29-2019, 05:05 PM Go to last post
  19. Need Help!- Hyundai HiT-18S: Spindle Clamp (M6/M7) Backwards

    Started by TC-Red‎, 06-12-2019 04:02 PM
    clamp, collet, machine, open, physically
    • Replies: 3
    • Views: 722
    06-14-2019, 12:42 PM Go to last post

Page 1 of 15 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands