Hyundai Kia

Page 1 of 15 123411 ... LastLast
Threads 1 to 20 of 293

Forum: Hyundai Kia

Discuss Hyundai Kia machines here.

  1. Hyundai Kia SKT 200 Alarms

    Started by RubenCarner‎, 05-28-2020 04:17 AM
    • Replies: 0
    • Views: 78
    05-28-2020, 04:17 AM Go to last post
  2. hyundai turning center problems

    Started by bbblackhills‎, 05-14-2020 09:55 AM
    center, control, error, hyundai, turning
    • Replies: 0
    • Views: 215
    05-14-2020, 09:55 AM Go to last post
  3. Hyundai HiT-18s Siemens hard drive replacement

    Started by svtford4x4‎, 11-03-2014 11:50 AM
    • Replies: 3
    • Views: 3,047
    03-29-2020, 12:14 AM Go to last post
  4. hit 15s manual (840c)

    Started by jonrya91‎, 03-21-2020 09:26 PM
    diagnose, helpful, machine, manual, wiring
    • Replies: 3
    • Views: 342
    03-24-2020, 03:30 AM Go to last post
  5. Parameters Hyundai Hit-15F

    Started by jgodwin16‎, 03-14-2020 10:45 PM
    • Replies: 2
    • Views: 234
    03-15-2020, 01:33 PM Go to last post
  6. Need Help!- Dangerous run a way X axis servo Kia Turn 21

    Started by shad061‎, 02-21-2020 02:44 AM
    alarm, circuit, issue, limit, switch
    • Replies: 0
    • Views: 417
    02-21-2020, 02:44 AM Go to last post
  7. Hit250m mr-j2s-100a-s046 turret servo drive

    Started by seraum‎, 01-24-2020 01:01 PM
    • Replies: 0
    • Views: 315
    01-24-2020, 01:01 PM Go to last post
  8. Post Need Help!- KIA 21LMS w Mitsubishi 520L control - Manuals Needed

    Started by vpcnc‎, 10-23-2019 11:13 AM
    kia, kia 21lms, manuals, mit 520l
    • Replies: 0
    • Views: 731
    10-23-2019, 11:13 AM Go to last post
  9. HiT 15s Spindle won't go over 70 rpm

    Started by jonrya91‎, 09-18-2019 07:09 AM
    • Replies: 3
    • Views: 769
    09-29-2019, 04:43 PM Go to last post
  10. Need Help!- Loading Hyundai Hit 20 parameters

    Started by taxslave‎, 09-03-2019 10:11 PM
    • Replies: 5
    • Views: 723
    09-26-2019, 02:05 PM Go to last post
  11. Need Help. Stuck in MDI mode.

    Started by 308billw‎, 09-10-2019 03:03 PM
    • Replies: 0
    • Views: 519
    09-10-2019, 03:03 PM Go to last post
  12. AL-4 Lubrication Oil Lack alarm

    Started by John-INTENSE‎, 05-20-2019 05:45 PM
    alarm, fluid, hydraulic, lubricant, specs
    • Replies: 3
    • Views: 783
    09-03-2019, 10:00 PM Go to last post
  13. STK 460

    Started by Dylan1985‎, 08-12-2019 07:58 PM
    aligned, it’s, moves, pressure, suggestions
    • Replies: 0
    • Views: 643
    08-12-2019, 07:58 PM Go to last post
  14. vx400 tool changer recovery

    Started by lakey0‎, 08-06-2019 10:55 AM
    change, cycle, recovery, rotated, tool
    • Replies: 1
    • Views: 569
    08-06-2019, 02:47 PM Go to last post
  15. Unhappy Need Help!- Turret Issue after Battery Dead Al-62 SKT21 LMS built 2010

    Started by HNiekamp‎, 07-19-2019 04:53 AM
    • Replies: 5
    • Views: 897
    07-29-2019, 05:05 PM Go to last post
  16. Need Help!- Hyundai HiT-18S: Spindle Clamp (M6/M7) Backwards

    Started by TC-Red‎, 06-12-2019 04:02 PM
    clamp, collet, machine, open, physically
    • Replies: 3
    • Views: 685
    06-14-2019, 12:42 PM Go to last post
  17. Hyundai-Kia VX500 Spindle V-Belt

    Started by LemmyRose‎, 05-20-2019 04:10 AM
    • Replies: 0
    • Views: 504
    05-20-2019, 04:10 AM Go to last post
  18. spindle load monitor on Hyundai machine

    Started by zavateandu‎, 05-08-2019 11:25 AM
    hyundai, load, macro, monitor, spindle
    • Replies: 0
    • Views: 546
    05-08-2019, 11:25 AM Go to last post
  19. SKT200 cooling fan errors.

    Started by CNCELOS‎, 04-07-2019 12:35 PM
    • Replies: 5
    • Views: 1,265
    04-12-2019, 05:39 PM Go to last post

Page 1 of 15 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 4 users browsing this forum. (0 members & 4 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands