HURCO

Page 1 of 69 12341151 ... LastLast
Threads 1 to 20 of 1369

Forum: HURCO

Discuss Hurco machines here.

  1. CNC MB-II

    Started by ahetland‎, 11-03-2018 11:36 AM
    • Replies: 0
    • Views: 91
    11-03-2018, 11:36 AM Go to last post
    • Replies: 8
    • Views: 703
    11-01-2018, 03:10 PM Go to last post
  2. Thoughts on upgrade from KMB1x to BMC 20?

    Started by m_mcgranahan‎, 10-23-2018 06:58 PM
    control, controller, kmb1x, stock, versus
    • Replies: 1
    • Views: 141
    10-24-2018, 01:39 AM Go to last post
  3. Hurcoo not downloading

    Started by tmccar‎, 10-20-2018 04:08 PM
    caused, cnc, disk, hard, hurco hawk
    • Replies: 0
    • Views: 194
    10-20-2018, 04:08 PM Go to last post
  4. Build Thread- Hurco KMB1 upgrade

    Started by FannBlade‎, 06-12-2013 12:34 AM
    7 Pages
    1 2 3 4 5 ... 7
    • Replies: 80
    • Views: 14,836
    10-14-2018, 02:10 PM Go to last post
  5. Need Help!- anyone know the beep codes for the lmb-680p motherboard

    Started by tony978‎, 10-12-2018 11:31 AM
    beep, codes, lmb-680p, pulling, ram
    • Replies: 0
    • Views: 94
    10-12-2018, 11:31 AM Go to last post
  6. Hurco KMB-1m Retrofit

    Started by Krell33‎, 01-19-2014 09:57 AM
    2 Pages
    1 2
    • Replies: 18
    • Views: 2,627
    10-03-2018, 02:38 PM Go to last post
  7. Need Help!- CMOS Battery Failure Hurco VM1

    Started by Dif‎, 05-24-2016 09:54 PM
    • Replies: 11
    • Views: 3,027
    10-02-2018, 04:53 PM Go to last post
  8. Need Help!- Hurco VM1 CMOS checksum error

    Started by eaglegage‎, 10-02-2018 01:15 PM
    checksum, cmos, error, hurco, vm1
    • Replies: 0
    • Views: 116
    10-02-2018, 01:15 PM Go to last post
  9. Need Help!- Hurco VM1 CMOS checksum error

    Started by eaglegage‎, 10-02-2018 01:01 PM
    checksum, cmos, error, hurco, vm1
    • Replies: 0
    • Views: 108
    10-02-2018, 01:01 PM Go to last post
  10. Need Help!- VM30i spindle won't start

    Started by PHAZER191‎, 09-25-2018 10:21 AM
    great, hurco, spindle, start, vm30i
    • Replies: 0
    • Views: 175
    09-25-2018, 10:21 AM Go to last post
  11. Need Help!- Servo jitters at idle

    Started by Sandvet03‎, 09-21-2018 12:35 PM
    amps, axis, servo, stays, swap
    • Replies: 2
    • Views: 175
    09-24-2018, 07:21 PM Go to last post
  12. Y axis home issue

    Started by Sandvet03‎, 09-22-2018 10:56 AM
    axis, fault, issue, machine, switch
    • Replies: 3
    • Views: 195
    09-22-2018, 11:07 PM Go to last post
  13. Video Hurco MB-1 Video Converter

    Started by tomtruty‎, 09-18-2018 04:49 PM
    converter, monitor, replacement, rgb, vga
    • Replies: 0
    • Views: 131
    09-18-2018, 04:49 PM Go to last post
    • Replies: 3
    • Views: 321
    09-13-2018, 08:44 PM Go to last post
  14. Need Help!- Hawk 5m wiring harness femal conector (Bloke?)

    Started by Sandvet03‎, 09-10-2018 08:45 PM
    good, harness, pins, servo, wire
    • Replies: 1
    • Views: 207
    09-11-2018, 07:49 AM Go to last post
  15. Thumbs up Need Help!- Searching for a working copy of Ulitmax PC - PC Plus.

    Started by skullworks‎, 08-21-2012 02:58 AM
    2 Pages
    1 2
    its, knows, maybe, plus, since, sliced
    • Replies: 18
    • Views: 2,070
    08-30-2018, 02:23 PM Go to last post
  16. Need Help!- Hurco PC Max software

    Started by underdog1495‎, 09-04-2014 10:35 AM
    already, cnc, computer, email, find, for sale, hobby, hobby cnc, home, hurco, install, key, lost, max, new computer, offline, offline software, pc-max, sale, softwar, software, stall, ultimax
    • Replies: 1
    • Views: 665
    08-30-2018, 11:19 AM Go to last post
  17. Need Help!- Ultimax km3p not detecting flopy discs

    Started by spectrumsas‎, 08-29-2018 01:33 PM
    .they, detect, disc, flopy, show
    • Replies: 0
    • Views: 126
    08-29-2018, 01:33 PM Go to last post

Page 1 of 69 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 15 users browsing this forum. (2 members & 13 guests)

  1. ronr,
  2. flyco1

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands