HURCO

Page 1 of 76 12341151 ... LastLast
Threads 1 to 20 of 1504

Forum: HURCO

Discuss Hurco machines here.

  1. Need Help!- Hurco Renishaw Macro - Probe Programming

    Started by Bogger24‎, 01-28-2019 04:47 PM
    find, hurco, macros, probe, renishaw
    • Replies: 2
    • Views: 885
    Today, 07:01 AM Go to last post
  2. Need Help!- Pins for km3p amphanol plug to servo motor

    Started by Jim-Michigan‎, 05-10-2021 07:44 PM
    amphanol, motors, pins, plug, servo
    • Replies: 0
    • Views: 244
    05-10-2021, 07:44 PM Go to last post
  3. Hurco bmc30htm console issues

    Started by Tiredeathracing‎, 05-09-2021 10:25 AM
    • Replies: 0
    • Views: 55
    05-09-2021, 10:25 AM Go to last post
  4. Hurco VMX42 ATC Slightly Out of Time

    Started by dmanthei‎, 04-28-2021 01:06 PM
    atc, back, chain, slightly, time
    • Replies: 0
    • Views: 1,393
    04-28-2021, 01:06 PM Go to last post
  5. Hurco BMC-20 Hard drive setup inquiry

    Started by tedhur‎, 04-10-2021 01:24 PM
    forum, hard, machines, setup, software
    • Replies: 18
    • Views: 437
    04-24-2021, 05:14 PM Go to last post
  6. Question Adding fourth Axis to Hurco VMC / Options?

    Started by hackbagger‎, 06-23-2010 12:05 PM
    almost, four, look, non
    • Replies: 16
    • Views: 7,612
    04-24-2021, 10:33 AM Go to last post
  7. Newbie- (Face milling/ Hurco WM10i) What is x corner and y corner?

    Started by 71gordi‎, 04-22-2021 01:11 PM
    appreciated, corner, face, mill, milling
    • Replies: 1
    • Views: 235
    04-22-2021, 10:20 PM Go to last post
  8. Hurco KM3/KM3P need servo cable connector pn

    Started by sitzme‎, 04-20-2021 11:21 AM
    cabinet, cable, end, plug, plugs
    • Replies: 1
    • Views: 117
    04-22-2021, 08:31 AM Go to last post
  9. Need Help!- VMX 24 Door issues Ultimax controller

    Started by 9566317‎, 04-15-2021 05:33 PM
    doors, machine, spindle, stops, tool
    • Replies: 0
    • Views: 471
    04-15-2021, 05:33 PM Go to last post
  10. Need Help!- HURCO KM5P Max 32/DSP hard drive type?

    Started by Rondal‎, 12-29-2020 06:23 PM
    check, hurco km5p memory, max, previous, settings
    • Replies: 5
    • Views: 425
    04-11-2021, 01:48 PM Go to last post
  11. Need Help!- The problem with the Hurco VMX 1 machine

    Started by Mr_Antonio‎, 04-08-2021 06:04 AM
    end, fittings, issues, message, problem
    • Replies: 0
    • Views: 365
    04-08-2021, 06:04 AM Go to last post
  12. Winmax V8.x locking up when loading programs...

    Started by gthlm‎, 04-05-2021 08:29 AM
    issue, machine, memory, programs, software
    • Replies: 0
    • Views: 181
    04-05-2021, 08:29 AM Go to last post
  13. Help with 2012 HURCO VM5i Winmax hard drive failure

    Started by jackgarner‎, 03-24-2021 01:17 AM
    hard drive
    • Replies: 1
    • Views: 725
    03-29-2021, 11:04 PM Go to last post
  14. Exclamation Need Help!- DANICHI 10T

    Started by Jrm75‎, 03-26-2021 04:04 AM
    axis, danichi, jog, manual, move
    • Replies: 0
    • Views: 179
    03-26-2021, 04:04 AM Go to last post
  15. Need Help!- hurco sm-1 electrical

    Started by davidg4‎, 09-30-2019 01:31 PM
    cnc, motor, operate, sm-1, spindle
    • Replies: 7
    • Views: 660
    03-26-2021, 03:36 AM Go to last post
  16. Question Need Help!- Hurco KM3P Servo Amplifier Fault "BIE"

    Started by msiminoff‎, 03-18-2021 11:28 AM
    • Replies: 4
    • Views: 844
    03-25-2021, 11:03 PM Go to last post
  17. Adding a second Screen?

    Started by TestingTesting123‎, 03-20-2021 03:05 PM
    connections, control, display, luck, screen
    • Replies: 0
    • Views: 215
    03-20-2021, 03:05 PM Go to last post
  18. adding a 4th axis.....

    Started by TestingTesting123‎, 02-28-2021 02:53 PM
    • Replies: 5
    • Views: 423
    03-17-2021, 12:45 PM Go to last post
  19. Need Help!- Hurco KM3P y-axis runaway

    Started by shaynut‎, 03-06-2021 10:45 AM
    • Replies: 11
    • Views: 635
    03-09-2021, 12:41 PM Go to last post

Page 1 of 76 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 17 users browsing this forum. (0 members & 17 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands