Hurco Hawk 2u Hard drive bad with ultipath Software

[Kcarpenter1986]

Hello,

Can any one help me. I have this small Hurco Hawk 2u

The control is ultipath

now the hard drive was bad in this when i got it and i have been using it as a manual mill for 6months or so but i want to get the cnc up and running now


The hard dive will not boot I have had the hard dive recovered and got as much data of it as i can. I have got a new hard drive in to it and loaded windows 98 (i belive the original was Windows 95 but i didnt have this) and it boots up windows. I have then copied all the dater from the old hard drive over and i can open the sortware but seams that only some bits of it work so i think to much is missing.

I have spoken with hurco and they seam to know nothing about this type of controller now. however they have send me 2 floppy disk (ultipath masters)

Disk one has Continue Execprog.001 and hurco.LDR on it

Disk 2 has execprog.002 and led_ed.LAN on it
I have tryed to boot these disks on Windows 98 and nothing happens


it seams that this controller from what I have been reading is verfy simuler to BMC30 but with a windows .... Is this correct? and if so do I load the software in the same kind of way?
I have found this https://docs.google.com/document/d/1...Byszi9LLU/edit
That says how to load a BMC30 and the files and names seam to very very simuler....

but if i need two partitions one C:/EXECUTIVE_1 and one D: /PART_PROGS where has windows got to be installed?

I do now have a copy of windows 95 that i can try but any help would be greatly appreciated from any one that knows any thing or that has one of these that might be able to help with DATA

I would like to try every thing i can on this controller before considering a retro fit

Thank you in advance

Similar Threads:

• Hurco SSM20 w/ Ultipath control
• HURCO BMC 40 New Hard Drive and now BAse Memory fault Less then 640kb
• Need Help!- Hurco BMC40 Hard Drive Replace
• hurco hawk spindle drive problems

[Kcarpenter1986]

any help any one?

[bloke]

It’s been a long while since I worked on an Ultipath control. By the sounds of it, you may have the wrong disks for it. Where are you in the world?

[Kcarpenter1986]

Hi Bloke.

Thanks for responding to me. I am in the Uk
I have been doing some diging on this again to night and it looks like you are right I think I have the wrong disks.

When I had the original drive recovered I got most of the data off but I am missing some on the files that seam to be needed to make the software run. What i need is somone with the disks of a hard drive I can copy.

What do you remember of the ultipath controll? where are you in the world?

Thank you for your help

[Kcarpenter1986]

I am based in norfolk near norwich.

[bloke]

I’m in Bucks. I’ll see if I can find some disks in the office. I should be back there tomorrow morning.

[Kcarpenter1986]

amazing thank you. do you work for hurco?

[bloke]

Good news! I had a trawl around my laptop and found two versions. PM me a mail address and I’ll bang ‘em over to you.
Yes I do.

[Kcarpenter1986]

amazing. thank you. so much. pm sent

[bpe]

I have just picked up on this thread I may have the discs you need and if you need any help i have a fully running 2 axis U2 but best of all I am 24 miles from Norwich give me a call if I can help in any way


Gordon

01952483640

[Kcarpenter1986]

Hi Gordon. thanks for getting back to you
I tried to call you but number seams to be wrong

would be nice to talk to you

mine is 07769721170

kc