Hobbycnc (Products)

Page 1 of 19 123411 ... LastLast
Threads 1 to 20 of 362

Forum: Hobbycnc (Products)

Discuss Hobbycnc controller boards here.

  1. CNC conversion Kits

    Started by Papajoeslc‎, 08-01-2019 02:06 PM
    • Replies: 1
    • Views: 238
    09-26-2019, 10:59 PM Go to last post
  2. Angry PoKeys57cnc to CW250 DRIVER wiring dilemma

    Started by iamlazee1‎, 09-07-2019 07:42 PM
    cw250, leading edge, pokeys57cnc
    • Replies: 0
    • Views: 123
    09-07-2019, 07:42 PM Go to last post
  3. Need Help!- okuma lb15 wilt osp5000 moves only in one direction

    Started by Reyad‎, 08-06-2019 12:09 PM
    axes, cnc, direction, lb15, moves
    • Replies: 0
    • Views: 392
    08-06-2019, 12:09 PM Go to last post
  4. New Machine Build- Adding ball screw to lathe for Electronic Lead Screw

    Started by harrzack‎, 12-28-2018 09:28 AM
    ball, ball screw selection, ball screws, diameter, screw
    • Replies: 0
    • Views: 637
    12-28-2018, 09:28 AM Go to last post
  5. Using mill table manually,, mach3 DRO readout

    Started by TheDude‎, 03-14-2008 06:32 AM
    2 Pages
    1 2
    another, mill table
    • Replies: 14
    • Views: 10,420
    12-20-2018, 08:56 AM Go to last post
  6. Amps vs motor vs controller?

    Started by JasC‎, 12-02-2018 05:04 PM
    amp, amps, brainer, controller, incase
    • Replies: 2
    • Views: 385
    12-02-2018, 10:24 PM Go to last post
  7. Would appreciate if someone told me what this is?

    Started by martijnvz‎, 11-10-2018 02:56 PM
    • Replies: 2
    • Views: 534
    11-12-2018, 03:20 AM Go to last post
    • Replies: 0
    • Views: 703
    02-25-2018, 05:17 PM Go to last post
  8. hobby cnc ez board trouble shooting help

    Started by rotccapt‎, 12-24-2017 10:41 AM
    2 Pages
    1 2
    • Replies: 16
    • Views: 1,384
    01-04-2018, 04:39 PM Go to last post
  9. HobbyCNC PRO Board Trouble shooting.

    Started by wjfiles‎, 05-06-2007 07:21 AM
    diag, not
    • Replies: 4
    • Views: 2,467
    12-26-2017, 11:15 AM Go to last post
  10. Will these stepper motors work?

    Started by SteveC68‎, 12-13-2017 02:42 PM
    board, compatible, steppers, steve, wondering
    • Replies: 1
    • Views: 527
    12-13-2017, 04:59 PM Go to last post
  11. What speeds are you getting with your EZ driver board?

    Started by Rat‎, 06-07-2017 09:07 PM
    5/16-18, minute, nema, screws, step/rev
    • Replies: 3
    • Views: 1,874
    10-26-2017, 06:03 PM Go to last post
  12. Newbie Q's

    Started by the_0utsid‎, 06-01-2017 12:36 AM
    cnc, move, power, stepper, supply
    • Replies: 1
    • Views: 622
    06-03-2017, 11:09 AM Go to last post
  13. Unhappy Need Help!- All axis move one direction

    Started by emba-media‎, 03-20-2017 01:48 PM
    change, changed, direction, mach3, move
    • Replies: 1
    • Views: 722
    03-20-2017, 02:29 PM Go to last post
  14. Need Help!- no axis movement

    Started by scottmcgraw‎, 02-19-2017 11:21 PM
    axis, board, current, minutes, posts
    • Replies: 2
    • Views: 684
    02-20-2017, 04:21 AM Go to last post
  15. YCM40 retrofit cnc

    Started by sil9mm‎, 02-12-2017 12:28 PM
    bob, cnc, lease, outdated, vfd
    • Replies: 1
    • Views: 541
    02-12-2017, 12:47 PM Go to last post
  16. Need Help!- Need help with 3040 CNC & Mach3 Settings.

    Started by sts2710‎, 01-30-2017 02:06 PM
    2 Pages
    1 2
    axis, cnc, mach3, motion, settings
    • Replies: 12
    • Views: 2,560
    02-04-2017, 05:21 PM Go to last post
  17. Z axis only moves in one direction

    Started by mklotz70‎, 08-21-2013 03:28 PM
    als, asking, away, cnc., everyone, since, then, went
    • Replies: 11
    • Views: 24,718
    12-18-2016, 09:31 AM Go to last post
  18. PROJECT-CNC ROUTER

    Started by optimist871‎, 11-26-2016 08:40 PM
    • Replies: 0
    • Views: 761
    11-26-2016, 08:40 PM Go to last post

Page 1 of 19 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands