Hobbycnc (Products)

Page 1 of 19 123411 ... LastLast
Threads 1 to 20 of 370

Forum: Hobbycnc (Products)

Discuss Hobbycnc controller boards here.

    • Replies: 0
    • Views: 135
    02-13-2021, 02:49 PM Go to last post
  1. Need Help!- GRBL spindle speed

    Started by bartekdko‎, 01-16-2021 02:08 PM
    8000rpm, grbl, set, speed, spindle
    • Replies: 0
    • Views: 358
    01-16-2021, 02:08 PM Go to last post
  2. Unhappy Need Help!- Loosing steps (?)

    Started by Firecnc‎, 01-12-2021 04:52 AM
    driver, motor, problem, run, test
    • Replies: 4
    • Views: 414
    01-14-2021, 09:59 AM Go to last post
  3. Help Needed: Identify controller board

    Started by rgfischerjr‎, 03-22-2020 10:15 AM
    • Replies: 2
    • Views: 941
    12-29-2020, 11:34 AM Go to last post
  4. Need Help!- okuma lb15 wilt osp5000 moves only in one direction

    Started by Reyad‎, 08-06-2019 01:09 PM
    axes, cnc, direction, lb15, moves
    • Replies: 1
    • Views: 3,043
    09-24-2020, 11:29 AM Go to last post
  5. Input Stopped Working

    Started by lowslo‎, 07-29-2020 07:27 PM
    cnc, pin, input, assigned, probe
    • Replies: 8
    • Views: 621
    08-01-2020, 04:04 PM Go to last post
  6. Z axis only moves in one direction

    Started by mklotz70‎, 08-21-2013 04:28 PM
    als, asking, away, cnc., everyone, since, then, went
    • Replies: 12
    • Views: 27,201
    05-06-2020, 11:55 AM Go to last post
  7. Just In Looking for set up ideas to use with existing legacy machine

    Started by jasonGO‎, 02-25-2020 05:08 PM
    accelus, computer, controllers, machine, running
    • Replies: 0
    • Views: 648
    02-25-2020, 05:08 PM Go to last post
  8. C77 - UC300ETH Multifunction Board?

    Started by rmachinist‎, 01-05-2020 09:17 PM
    board, c77, multifunction, run, uc300eth
    • Replies: 0
    • Views: 1,477
    01-05-2020, 09:17 PM Go to last post
  9. CNC conversion Kits

    Started by Papajoeslc‎, 08-01-2019 03:06 PM
    • Replies: 1
    • Views: 1,345
    09-26-2019, 11:59 PM Go to last post
  10. Angry PoKeys57cnc to CW250 DRIVER wiring dilemma

    Started by iamlazee1‎, 09-07-2019 08:42 PM
    cw250, leading edge, pokeys57cnc
    • Replies: 0
    • Views: 759
    09-07-2019, 08:42 PM Go to last post
  11. New Machine Build- Adding ball screw to lathe for Electronic Lead Screw

    Started by harrzack‎, 12-28-2018 10:28 AM
    ball, ball screw selection, ball screws, diameter, screw
    • Replies: 0
    • Views: 1,347
    12-28-2018, 10:28 AM Go to last post
  12. Using mill table manually,, mach3 DRO readout

    Started by TheDude‎, 03-14-2008 07:32 AM
    another, mill table
    • Replies: 14
    • Views: 11,748
    12-20-2018, 09:56 AM Go to last post
  13. Amps vs motor vs controller?

    Started by JasC‎, 12-02-2018 06:04 PM
    amp, amps, brainer, controller, incase
    • Replies: 2
    • Views: 990
    12-02-2018, 11:24 PM Go to last post
  14. Would appreciate if someone told me what this is?

    Started by martijnvz‎, 11-10-2018 03:56 PM
    • Replies: 2
    • Views: 1,093
    11-12-2018, 04:20 AM Go to last post
    • Replies: 0
    • Views: 1,205
    02-25-2018, 06:17 PM Go to last post
  15. hobby cnc ez board trouble shooting help

    Started by rotccapt‎, 12-24-2017 11:41 AM
    • Replies: 16
    • Views: 2,153
    01-04-2018, 05:39 PM Go to last post
  16. HobbyCNC PRO Board Trouble shooting.

    Started by wjfiles‎, 05-06-2007 08:21 AM
    diag, not
    • Replies: 4
    • Views: 3,759
    12-26-2017, 12:15 PM Go to last post

Page 1 of 19 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands