Hobbycnc (Products)

Page 1 of 19 123411 ... LastLast
Threads 1 to 20 of 370

Forum: Hobbycnc (Products)

Discuss Hobbycnc controller boards here.

  1. dave, How is 23-200-DS8 Unipolar Stepper 8 wire work?

    Started by cjchands‎, 10-15-2006 07:14 PM
    200oz-in, 23-200-ds, bipolar, cnc, oz.in, said, unipolar, wire, work
    • Replies: 3
    • Views: 3,920
    03-19-2021, 10:37 AM Go to last post
    • Replies: 0
    • Views: 330
    02-13-2021, 01:49 PM Go to last post
  2. Need Help!- GRBL spindle speed

    Started by bartekdko‎, 01-16-2021 01:08 PM
    8000rpm, grbl, set, speed, spindle
    • Replies: 0
    • Views: 545
    01-16-2021, 01:08 PM Go to last post
  3. Unhappy Need Help!- Loosing steps (?)

    Started by Firecnc‎, 01-12-2021 03:52 AM
    driver, motor, problem, run, test
    • Replies: 4
    • Views: 566
    01-14-2021, 08:59 AM Go to last post
  4. Help Needed: Identify controller board

    Started by rgfischerjr‎, 03-22-2020 09:15 AM
    • Replies: 2
    • Views: 1,046
    12-29-2020, 10:34 AM Go to last post
  5. Need Help!- okuma lb15 wilt osp5000 moves only in one direction

    Started by Reyad‎, 08-06-2019 12:09 PM
    axes, cnc, direction, lb15, moves
    • Replies: 1
    • Views: 3,154
    09-24-2020, 10:29 AM Go to last post
  6. Input Stopped Working

    Started by lowslo‎, 07-29-2020 06:27 PM
    cnc, pin, input, assigned, probe
    • Replies: 8
    • Views: 728
    08-01-2020, 03:04 PM Go to last post
  7. Z axis only moves in one direction

    Started by mklotz70‎, 08-21-2013 03:28 PM
    als, asking, away, cnc., everyone, since, then, went
    • Replies: 12
    • Views: 27,469
    05-06-2020, 10:55 AM Go to last post
  8. Just In Looking for set up ideas to use with existing legacy machine

    Started by jasonGO‎, 02-25-2020 04:08 PM
    accelus, computer, controllers, machine, running
    • Replies: 0
    • Views: 695
    02-25-2020, 04:08 PM Go to last post
  9. C77 - UC300ETH Multifunction Board?

    Started by rmachinist‎, 01-05-2020 08:17 PM
    board, c77, multifunction, run, uc300eth
    • Replies: 0
    • Views: 1,514
    01-05-2020, 08:17 PM Go to last post
  10. CNC conversion Kits

    Started by Papajoeslc‎, 08-01-2019 02:06 PM
    • Replies: 1
    • Views: 1,405
    09-26-2019, 10:59 PM Go to last post
  11. Angry PoKeys57cnc to CW250 DRIVER wiring dilemma

    Started by iamlazee1‎, 09-07-2019 07:42 PM
    cw250, leading edge, pokeys57cnc
    • Replies: 0
    • Views: 809
    09-07-2019, 07:42 PM Go to last post
  12. New Machine Build- Adding ball screw to lathe for Electronic Lead Screw

    Started by harrzack‎, 12-28-2018 09:28 AM
    ball, ball screw selection, ball screws, diameter, screw
    • Replies: 0
    • Views: 1,397
    12-28-2018, 09:28 AM Go to last post
  13. Using mill table manually,, mach3 DRO readout

    Started by TheDude‎, 03-14-2008 06:32 AM
    another, mill table
    • Replies: 14
    • Views: 11,896
    12-20-2018, 08:56 AM Go to last post
  14. Amps vs motor vs controller?

    Started by JasC‎, 12-02-2018 05:04 PM
    amp, amps, brainer, controller, incase
    • Replies: 2
    • Views: 1,040
    12-02-2018, 10:24 PM Go to last post
  15. Would appreciate if someone told me what this is?

    Started by martijnvz‎, 11-10-2018 02:56 PM
    • Replies: 2
    • Views: 1,141
    11-12-2018, 03:20 AM Go to last post
    • Replies: 0
    • Views: 1,249
    02-25-2018, 05:17 PM Go to last post
  16. hobby cnc ez board trouble shooting help

    Started by rotccapt‎, 12-24-2017 10:41 AM
    • Replies: 16
    • Views: 2,215
    01-04-2018, 04:39 PM Go to last post

Page 1 of 19 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands