Hitachi Seikis

Page 1 of 12 123411 ... LastLast
Threads 1 to 20 of 234

Forum: Hitachi Seikis

Discuss Hitachi Seikis here!

    • Replies: 4
    • Views: 262
    06-02-2018, 03:29 AM Go to last post
  1. Need Help!- VS50 Issues after transportation

    Started by caseybarsness‎, 05-23-2018 07:17 PM
    atc, axis, cycle, machine, powering
    • Replies: 2
    • Views: 162
    05-29-2018, 03:30 PM Go to last post
  2. Hitachi Seiki Repair / Service / Support

    Started by shas595‎, 06-15-2015 09:31 AM
    5 Pages
    1 2 3 4 5
    • Replies: 48
    • Views: 3,162
    05-24-2018, 10:52 AM Go to last post
  3. VS50 +X over travel alarm

    Started by WC56‎, 04-09-2018 01:48 AM
    alarm, atc, move, tool, travel
    • Replies: 6
    • Views: 298
    05-23-2018, 07:00 AM Go to last post
  4. Need Help!- What is the SL Bus?

    Started by MWinrich-KMC‎, 05-14-2018 12:50 PM
    bus, error, i/o, machine, slbus
    • Replies: 1
    • Views: 128
    05-14-2018, 02:30 PM Go to last post
  5. Need Help!- Hitachi Seiki VM40 ladder back up

    Started by mnankov‎, 04-30-2018 02:02 AM
    backup, hitachi, ladder, seiki, vm40
    • Replies: 2
    • Views: 228
    05-12-2018, 02:33 AM Go to last post
  6. Run program from computer via RS232 (aka DNC)

    Started by =aike=‎, 04-22-2018 11:21 AM
    cnc, computer, load, program, run
    • Replies: 5
    • Views: 273
    04-24-2018, 02:38 AM Go to last post
    • Replies: 4
    • Views: 411
    04-03-2018, 07:43 PM Go to last post
  7. HiCell 23B - Polar interpolation

    Started by marcin75‎, 04-02-2018 11:16 AM
    • Replies: 0
    • Views: 87
    04-02-2018, 11:16 AM Go to last post
  8. Problem- Control alarms

    Started by BOBTEAM‎, 03-08-2018 03:58 PM
    alarms, batteries, control, disconnected, error
    • Replies: 3
    • Views: 433
    03-13-2018, 12:28 PM Go to last post
  9. Need Help!- VS50 DNC problem

    Started by WC56‎, 03-12-2018 04:26 AM
    cable, dnc, rs232, screen, send
    • Replies: 0
    • Views: 189
    03-12-2018, 04:26 AM Go to last post
  10. Hitachi Seikis VK45 II - Seicos M3 - Error 867

    Started by firstreal‎, 02-20-2018 05:37 AM
    • Replies: 4
    • Views: 558
    03-01-2018, 08:31 AM Go to last post
  11. Need Help!- 5NE-1100

    Started by juanfmoralese‎, 02-13-2018 10:12 PM
    5ne-1100, control, fanuc, lathe, seiki
    • Replies: 0
    • Views: 210
    02-13-2018, 10:12 PM Go to last post
  12. 3NE-300 drawings

    Started by Lary Alvey‎, 02-04-2014 10:40 AM
    3ne
    • Replies: 2
    • Views: 574
    02-02-2018, 06:18 PM Go to last post
  13. Exclamation Problem- Hitachi 23B hicell Seicos LIII not working

    Started by xxx83‎, 12-26-2017 01:06 PM
    • Replies: 11
    • Views: 693
    01-19-2018, 02:06 AM Go to last post
  14. Need Help!- Hitachi Seiki HC400 All Over Travel Alarm

    Started by Billet Carb‎, 01-16-2018 04:21 PM
    hc 400 overtravel alarms, machine, problem, received, voltage
    • Replies: 0
    • Views: 200
    01-16-2018, 04:21 PM Go to last post
  15. Problem- Hitachi Seiki 3 NE -300

    Started by Falcone‎, 01-11-2018 10:21 AM
    deleted, hitachi, program, programs, seiki
    • Replies: 2
    • Views: 202
    01-11-2018, 10:38 AM Go to last post
  16. Seicos III, battery dead? software reload? How bad is this?

    Started by bob1112‎, 09-06-2017 09:29 PM
    2 Pages
    1 2
    battery, dead, pretty, reload, software
    • Replies: 14
    • Views: 615
    12-13-2017, 04:54 PM Go to last post
    • Replies: 0
    • Views: 336
    12-06-2017, 03:08 PM Go to last post
  17. Problem- Plase help. Hitachi Seiki Hg400 Micon 16-3 ladder upload??

    Started by mguven‎, 05-10-2017 02:54 AM
    ladder, machine, seiki, software, upload
    • Replies: 4
    • Views: 488
    12-04-2017, 01:24 AM Go to last post

Page 1 of 12 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 10 users browsing this forum. (0 members & 10 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands