Hitachi Seikis

Page 1 of 18 123411 ... LastLast
Threads 1 to 20 of 357

Forum: Hitachi Seikis

Discuss Hitachi Seikis here!

  1. Need Help!- Hitachi Seiki 20SII switched to metric after changing battery

    Started by JGRACE‎, 01-14-2022 01:16 PM
    back, battery, metric, program, switches
    • Replies: 1
    • Views: 78
    01-14-2022, 06:11 PM Go to last post
  2. Hitachi Seiki AUTO-programing manual

    Started by nemad668‎, 01-02-2022 07:12 AM
    • Replies: 0
    • Views: 90
    01-02-2022, 07:12 AM Go to last post
  3. Need Help!- Need Help

    Started by h65‎, 12-15-2021 09:35 AM
    good, green, parameters, power, turret
    • Replies: 0
    • Views: 240
    12-15-2021, 09:35 AM Go to last post
  4. Hitachi seiki h cut 230 m

    Started by Mohammad_sh‎, 12-11-2021 06:06 AM
    cut, hitachi, increase, limited, page
    • Replies: 0
    • Views: 386
    12-11-2021, 06:06 AM Go to last post
  5. Hitachi Seiki Alarm Help!

    Started by stevo1‎, 06-16-2008 10:09 AM
    not
    • Replies: 8
    • Views: 6,563
    12-11-2021, 04:47 AM Go to last post
  6. Va-40 atc problem

    Started by MwTechInc‎, 12-09-2021 03:27 PM
    atc, imp, reset, sequence, tool
    • Replies: 1
    • Views: 188
    12-09-2021, 05:43 PM Go to last post
  7. Seicos Slbus error- Fanuc 18-ima

    Started by freemanxxx‎, 08-24-2017 07:12 PM
    error, fanuc, machine, seicos, slbus
    • Replies: 1
    • Views: 996
    12-07-2021, 04:25 PM Go to last post
  8. VS40 TOOL CAROUSEL HOME POSITION

    Started by Micwanho‎, 07-24-2021 10:15 PM
    • Replies: 2
    • Views: 494
    12-07-2021, 04:07 PM Go to last post
  9. Va-40 pull stud question

    Started by MwTechInc‎, 11-22-2021 10:58 AM
    • Replies: 6
    • Views: 230
    12-07-2021, 03:46 PM Go to last post
  10. va-40 Micron 8 troubleshooting

    Started by MwTechInc‎, 12-01-2021 06:49 PM
    lube, panel, side, signal, start
    • Replies: 1
    • Views: 174
    12-02-2021, 04:29 PM Go to last post
    • Replies: 0
    • Views: 268
    11-15-2021, 04:24 PM Go to last post
  11. Need Help!- Hitachi Seiki HG500 data loading from pc to micon16-iii

    Started by mozturk‎, 11-05-2021 04:01 AM
    diagram, download, hg500, upload, wiring
    • Replies: 1
    • Views: 279
    11-15-2021, 08:04 AM Go to last post
  12. Need Help!- HiCell CA40II - tool registration by program

    Started by jjjearls‎, 10-29-2021 03:41 PM
    change, hicell, tool, tools, turret
    • Replies: 0
    • Views: 246
    10-29-2021, 03:41 PM Go to last post
  13. Need Help!- Parameter list

    Started by L98FIERO‎, 10-28-2021 11:27 AM
    list, mx3, parameter, seicos, working
    • Replies: 2
    • Views: 200
    10-28-2021, 11:49 AM Go to last post
  14. Hitachi seiki vs 60

    Started by salas‎, 10-12-2021 12:55 AM
    atc, button, clamp, press, unclamp
    • Replies: 0
    • Views: 285
    10-12-2021, 12:55 AM Go to last post
  15. Need Help!- VS 60

    Started by salas‎, 10-09-2021 09:49 PM
    alguien, ayudar, levas, puerta, unidad
    • Replies: 0
    • Views: 280
    10-09-2021, 09:49 PM Go to last post
  16. Need Help!- HITACHI SEIKI VM40 SEICOS MYIII option param

    Started by kiss‎, 10-06-2021 03:18 AM
    jana, machine, options, parameters, works
    • Replies: 1
    • Views: 278
    10-06-2021, 09:02 PM Go to last post
  17. Need Help!- Hitachi VK45 seicos m3 1016 RAM error

    Started by 1970gobg‎, 10-05-2021 01:32 PM
    alarm, card, leds, lit, red
    • Replies: 0
    • Views: 385
    10-05-2021, 01:32 PM Go to last post
  18. Post Solved Hitachi Seiki HC400 - FANUC 15M NC and PC Parameters

    Started by ivan360‎, 09-29-2021 07:40 PM
    • Replies: 0
    • Views: 273
    09-29-2021, 07:40 PM Go to last post

Page 1 of 18 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 3 users browsing this forum. (0 members & 3 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands