Hitachi Seikis

Page 1 of 22 123411 ... LastLast
Threads 1 to 20 of 427

Forum: Hitachi Seikis

Discuss Hitachi Seikis here!

  1. Hitachi Seiki Repair / Service / Support

    Started by shas595‎, 06-15-2015 09:31 AM
    10 Pages
    1 2 3 4 5 ... 10
    • Replies: 185
    • Views: 41,512
    09-29-2024, 05:32 AM Go to last post
    • Replies: 0
    • Views: 707
    08-09-2024, 09:13 AM Go to last post
  2. Hitachi Seiki HITEC-TURN 40 S

    Started by Szprycha‎, 08-03-2024 08:39 AM
    • Replies: 0
    • Views: 236
    08-03-2024, 08:39 AM Go to last post
  3. Need Help!- Machine not ready Help !!

    Started by cambo747‎, 07-19-2024 07:10 PM
    hitachi, machine, ready, track
    • Replies: 0
    • Views: 704
    07-19-2024, 07:10 PM Go to last post
  4. Need Help!- Collision alarm 1187 on Z-axis when at 50% on rapid

    Started by jjjearls‎, 07-10-2024 07:14 PM
    alarm, collision, movements, rapid, running
    • Replies: 3
    • Views: 472
    07-11-2024, 09:34 PM Go to last post
  5. TF-15 parameters / manuals / software

    Started by hwgasdfasdf‎, 06-05-2024 03:28 PM
    machine, manuals, parameters, repair, software
    • Replies: 7
    • Views: 897
    07-02-2024, 01:13 PM Go to last post
    • Replies: 2
    • Views: 876
    06-27-2024, 10:20 PM Go to last post
  6. Exclamation Need Help!- Hitachi-Seiki 23R - ACGC UNREADY

    Started by AndyM23‎, 06-14-2024 11:14 AM
    acgc, check, pass, system, unready
    • Replies: 1
    • Views: 586
    06-16-2024, 08:18 AM Go to last post
  7. Newbie- Hitachi seiki hg 400 III M16

    Started by ABDELSIOUD‎, 04-14-2024 06:20 AM
    hitachi, iii, m16, machine, seiki
    • Replies: 1
    • Views: 1,370
    06-10-2024, 06:01 PM Go to last post
  8. TS-15 multiple alarms on startup

    Started by cbChris‎, 05-09-2024 11:01 AM
    ts-15, alarms, reload, response, lost
    • Replies: 2
    • Views: 667
    05-11-2024, 08:38 AM Go to last post
  9. Hitachi seiki 3ne 300 6t

    Started by Palmerc‎, 04-02-2024 01:22 PM
    back, machine, program, run, turret
    • Replies: 1
    • Views: 702
    04-02-2024, 03:01 PM Go to last post
  10. Hitachi Seiki 3NE-300 Motor Alarm - Help!

    Started by jennerjh‎, 02-23-2024 04:01 PM
    • Replies: 1
    • Views: 3,964
    02-26-2024, 12:52 PM Go to last post
  11. Lost Parameter Hitachi Seiki HG400II with Fanuc 15m

    Started by funuman‎, 02-01-2024 05:44 AM
    15m, fanuc, hg400ii, hitachi, seiki
    • Replies: 0
    • Views: 1,893
    02-01-2024, 05:44 AM Go to last post
  12. HT20 Membrane replacement

    Started by dbramley‎, 01-29-2024 04:41 PM
    butt, control, dan, machinist, membrane
    • Replies: 0
    • Views: 1,405
    01-29-2024, 04:41 PM Go to last post
    • Replies: 1
    • Views: 1,734
    01-10-2024, 05:37 PM Go to last post
  13. Hitachi Seiki Ye-Net error

    Started by G91guy‎, 08-11-2014 07:58 AM
    alarm, appreciated, art, control, correct, down, error, hitachi, hitachi seiki, i/o, iii, machine, net, no.1, restart, run, running, seiki, shop, small, stop, then, yasnac, ye-net
    • Replies: 3
    • Views: 2,595
    12-19-2023, 04:44 PM Go to last post
  14. Hitachi Seiki Hg400III NC Communications Error

    Started by Tgilbert‎, 12-05-2023 04:47 PM
    hitachi seiki hg400iii
    • Replies: 0
    • Views: 1,042
    12-05-2023, 04:47 PM Go to last post
  15. Need Help!- HT 23 lathe won’t power up

    Started by muhlenm‎, 11-26-2023 08:27 PM
    booted, machine, outage, power, start
    • Replies: 1
    • Views: 2,499
    11-27-2023, 06:02 AM Go to last post
    • Replies: 13
    • Views: 4,948
    11-27-2023, 03:49 AM Go to last post
  16. Thumbs up Hitach Seiki V60

    Started by ali1354‎, 11-26-2023 02:21 AM
    experance, issue, machine, seiki, thank you so much
    • Replies: 0
    • Views: 2,415
    11-26-2023, 02:21 AM Go to last post

Page 1 of 22 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands