Hitachi Seikis

Page 1 of 17 123411 ... LastLast
Threads 1 to 20 of 332

Forum: Hitachi Seikis

Discuss Hitachi Seikis here!

  1. VS40 TOOL CAROUSEL HOME POSITION

    Started by Micwanho‎, 07-24-2021 09:15 PM
    carousel, correct, establish, procedure, tool
    • Replies: 1
    • Views: 195
    07-30-2021, 01:16 AM Go to last post
  2. hitachi seiki hi tech turn 30

    Started by HTTROUBLE‎, 07-19-2021 03:10 PM
    alarm, clear, instruction, seiki, tech
    • Replies: 0
    • Views: 170
    07-19-2021, 03:10 PM Go to last post
  3. Hitachi seiki HT20J with 3299 ye-net i/o error

    Started by KAKI‎, 07-03-2021 02:50 PM
    cables, error, hitachi, machine, suggest
    • Replies: 0
    • Views: 295
    07-03-2021, 02:50 PM Go to last post
    • Replies: 2
    • Views: 1,336
    06-30-2021, 05:44 AM Go to last post
  4. Unhappy Problem- Hitachi Seiki VK45 II Programm transfer

    Started by Moiya‎, 06-24-2021 04:15 AM
    • Replies: 2
    • Views: 230
    06-26-2021, 03:20 AM Go to last post
  5. Exclamation Need Help!- HiCell 23 Zero Point Dog Adjustment

    Started by caseybarsness‎, 07-11-2019 01:04 PM
    adjustment, casey, manual, operation, point
    • Replies: 2
    • Views: 1,120
    06-21-2021, 10:44 PM Go to last post
  6. Need Help!- How to replace servo drive in HITACHI HG400III

    Started by =aike=‎, 04-15-2021 05:18 AM
    • Replies: 7
    • Views: 535
    06-11-2021, 10:31 AM Go to last post
  7. HELP! Hitachi Seiki HT-25G HPC1 lost configuration

    Started by ph0ngvu‎, 05-08-2021 04:54 AM
    • Replies: 1
    • Views: 871
    05-27-2021, 11:26 PM Go to last post
  8. Need Help!- Hitachi seiki lathe HT 20j seicos j multi

    Started by Leon2001‎, 05-21-2021 02:14 PM
    familiar, hitachi, program, run, seicos
    • Replies: 1
    • Views: 268
    05-21-2021, 07:35 PM Go to last post
  9. Help Seicos Lambda 10L

    Started by terminaterx300‎, 05-11-2019 10:12 PM
    data, eventhrough, hdd, read, unable
    • Replies: 3
    • Views: 1,155
    04-30-2021, 06:09 PM Go to last post
  10. Need Help!- KEYBOARD UNCONFIGURED - HITACHI SEIKI HT30J lathe

    Started by Chivo‎, 04-28-2021 01:03 AM
    interface, keyboard, machine, remove, seicos
    • Replies: 0
    • Views: 257
    04-28-2021, 01:03 AM Go to last post
    • Replies: 2
    • Views: 1,753
    04-16-2021, 11:24 PM Go to last post
  11. Need Help!- HiCell 23 Turret Not Indexing!

    Started by caseybarsness‎, 03-16-2021 10:15 PM
    hicell, index, mode, program, turret
    • Replies: 1
    • Views: 453
    04-15-2021, 05:47 PM Go to last post
  12. Hitachi Seiki HT 25R Yasnac J50L Parameter List

    Started by gsjin‎, 02-16-2021 07:27 PM
    • Replies: 2
    • Views: 473
    04-09-2021, 05:21 AM Go to last post
  13. Hitachi CS20 lost 7mm in x after a power blip

    Started by Stefkorn‎, 03-17-2021 03:23 AM
    7mm, amp, amps, axis, servo
    • Replies: 0
    • Views: 2,359
    03-17-2021, 03:23 AM Go to last post
    • Replies: 2
    • Views: 1,079
    03-16-2021, 09:15 AM Go to last post
    • Replies: 2
    • Views: 657
    02-23-2021, 03:50 AM Go to last post
  14. Need Help!- Hitachi Seiki Hi-Cell CA 23B [1039] RAM error

    Started by Loxer‎, 02-19-2021 02:40 PM
    • Replies: 0
    • Views: 601
    02-19-2021, 02:40 PM Go to last post
  15. Alarm 14 on HT20SII with Multi (LX3) control

    Started by zombie1363‎, 01-16-2021 07:14 PM
    al-14, alarm 14, alm 543, ht20sii, lx3
    • Replies: 0
    • Views: 427
    01-16-2021, 07:14 PM Go to last post
  16. Drive Hitachi Seiki VK45 II

    Started by firstreal‎, 10-31-2016 03:48 AM
    • Replies: 3
    • Views: 760
    01-14-2021, 09:52 AM Go to last post

Page 1 of 17 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands