Hitachi Seiki Repair / Service / Support - Page 5

Page 5 of 5 FirstFirst ... 2345
Results 49 to 57 of 57

Thread: Hitachi Seiki Repair / Service / Support

  1. #49
    Registered shas595's Avatar
    Join Date
    Dec 2009
    Location
    United States
    Posts
    423
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Repair / Service / Support

    Tony

    I sent you an email - take a look, will need some more info before i can help out

    John



  2. #50
    *Registered User* hamidreza1356's Avatar
    Join Date
    Jul 2018
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default

    Hi dears
    I have a hitachi Seiki center with HBG630 model and Fanuc 15M control.already cleard the Ram and I don't have any backup of it. Now I have a problem on tapping cycle,Can anybody help me about the programming tapping cycle please?
    In addition cycle g84 doesn't work and tool change doesn't reserve and ready io program.Thanks a lot.

    Last edited by hamidreza1356; 07-08-2018 at 12:51 AM.


  3. #51
    Registered shas595's Avatar
    Join Date
    Dec 2009
    Location
    United States
    Posts
    423
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Repair / Service / Support

    hello!

    What do you mean cleared the RAM? What was the issue that caused you to clear the data? What data did you have to enter?



  4. #52
    *Registered User* hamidreza1356's Avatar
    Join Date
    Jul 2018
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Repair / Service / Support

    Hi friend
    The memory of Ram card with A16B 2200 013 was cleard and the service man reinstalled
    The Ram card and wrote the program macros.
    But now I knew there are problem on tapping cycle and tool changing.
    G84 doesn't work. And I have to work with G84.2 when start the program tapping the axis move to forward and when it will backward , the tap will break.and the other problem is on the tool changing. When the program start, the machine have to ready next tool for next op but it doesn't do this.
    Help me plz.
    Thanks guy.



  5. #53
    pedro68's Avatar
    Join Date
    Sep 2018
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    Hi i ma new in this forum, Someone can i help me becouse a have a pin lathe hitachi seiki ht-25s and i don`t have the manuals technicians , i can not to star



  6. #54
    Registered
    Join Date
    Sep 2011
    Location
    united states
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default

    I have Hitec turn 20SII with a 173 parameter error. I need parameter sheet. My sn. Is HTS2399HL. Van you tell me how to fix. Any help would be appreciated.



  7. #55
    Registered shas595's Avatar
    Join Date
    Dec 2009
    Location
    United States
    Posts
    423
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Repair / Service / Support

    Hello

    send me a PM with more info

    John



  8. #56
    *Registered User* Brunocnc28's Avatar
    Join Date
    Aug 2018
    Posts
    19
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Repair / Service / Support

    Hi
    Is There somebody who have knowledge on a Hicell with complete Nec control ( Nc and servo, only spindle is yaskawa 626VM3)
    Thanks.



  9. #57
    Registered shas595's Avatar
    Join Date
    Dec 2009
    Location
    United States
    Posts
    423
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Repair / Service / Support

    Hello!
    yes I do - if you want you can PM me your email and Ill help you out!
    john



  10. #58
    Registered
    Join Date
    Nov 2012
    Location
    Poland
    Posts
    12
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Repair / Service / Support

    Few days ago got one scary situation, after probing part on vm50 when I hit cycle start Z Axis instead of going on to Z0 g28 , dropped into the part like it's freefalling , immediately pressed the estop and there was nc servo alarm and 1219 z innefective current over . Had to restart the pc because I couldnt jog the tool of the part. IT looks like the brake on the Z Axis didnt worked as its should ? Is it a sign of the nc control ending it's lifespan or servo ? When the machine idles on the screen I can see 65% when it was jogged to up or 50% when was jogging down Z Axis load . It's 98 model.



  11. #59
    David12's Avatar
    Join Date
    Nov 2018
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    Hello i'm french i need your help . Can you help me for a problem with hitachi seiki seicos 10. Thank's



  12. #60
    Registered
    Join Date
    Nov 2012
    Location
    Poland
    Posts
    12
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Repair / Service / Support

    My Hitachi vm50 got Orange screen , machine was staying idle then suddenly black screen appeared and everything was shutdown. Is it something with graphic card ,or LCD ? Or its the NC Control that is down?



Page 5 of 5 FirstFirst ... 2345

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Hitachi Seiki Repair / Service / Support

Hitachi Seiki Repair / Service / Support