Hitachi Seiki Repair / Service / Support

[Muciek]

Pm John here he is very helpfull , should hook you up with books or some info.

[L98FIERO]

Does anyone know the parameter to turn on the M8 (mist) option and the macro option? It's for a Matsuura MC-510V with a Yasnac MX-3 control. A options parameter list would be great if possible.

[Dancy]

shas595 (John?)
short question for you. On a hitachi Seiki Micon-16, Seicos-II, when the battery dies you loose slbus data and parameters. Is the ladder lost or does that happen because of other problems?

Dan

[Hitachi-parts-usa]

Hello Dan,
If John can not help you. WE would be happy to assist it sounds like you need a reload on your seiki. Let us know if you need any information about your machine or parts as we have a vast inventory of parts available. cybermachinery@gmail.com.
-A.J

[Hitachi-parts-usa]

Hello Vanki if you still need help with your VS50 we have parameters as well as loading procedures amongst parts for your Seiki machine. Contact us directly at cybermachinery@gmail.com.
We will be happy to assist.
-A.J

[shas595]

Dan
Yes that is correct. When the battery goes you lose it all

PM me if you need more info
John

shas595 (John?)
short question for you. On a hitachi Seiki Micon-16, Seicos-II, when the battery dies you loose slbus data and parameters. Is the ladder lost or does that happen because of other problems?

Dan

Sent from my iPhone using Tapatalk

[Dancy]

Hello Dan,
If John can not help you. WE would be happy to assist it sounds like you need a reload on your seiki. Let us know if you need any information about your machine or parts as we have a vast inventory of parts available. cybermachinery@gmail.com.
-A.J

Thanks AJ;
short question: is the ladder lost on battery failure?

I have a doc from Hitachi that implies no.
SV03-999-62-010 instructs how to swap the ROM chips

[cncmakers001]

Hi all,
I have a Hitachi Seiki VM40 and I want to redo the electronics, so the plan is to replace X, Y & Z drive motors and drives and only keep the current spindle and spindle drive which are Fanuc, the motor is A06B-1003-B300 and the Control unit is A06B-6044-H103. I am not fused about being able to tap and cut threads so if someone could suggest a simpler spindle I would be happy to change. Sadly I don't have any circuit diagrams as I had someone else helping and they dropped off the edge of the world with my books.
Plan is to use Centroid equipment were possible.
Any help would be greatly appreciated.
Tony

It is better to change the AC servo spindle motors and drivers too, to get the best performance and best compatibility.

[Dancy]

Hello Dan,
If John can not help you. WE would be happy to assist it sounds like you need a reload on your seiki. Let us know if you need any information about your machine or parts as we have a vast inventory of parts available. cybermachinery@gmail.com.
-A.J

AJ...your email box is full

[xuyuanlin]

hello ,i lost my Hitachi Seiki TF-20 Powermate sram,i need you help! can someone send it to me? or i can pay for it , thanks!! my gmail :520xuyuanlin@gmail.com

[alfredosindona]

hi i have a problem on a vk45II machine with SEICOS lampda 10M. Error 699 Directory broken Can you help me?

[shas595]

hi i have a problem on a vk45II machine with SEICOS lampda 10M. Error 699 Directory broken Can you help me?

Yes send me an PM and I will help you out

John


Sent from my iPhone using Tapatalk

[alfredosindona]

hi i have a problem on a vk45II machine with SEICOS lampda 10M. Error 699 Directory broken Can you help me?

[shas595]

I sent you a message take a look
John

hi i have a problem on a vk45II machine with SEICOS lampda 10M. Error 699 Directory broken Can you help me?

[kiss]

dear friends,
i have hitachi seiki vm40 with seicos my3...
after on:
it cannot to booting because : motion rtc unready...alarm,
the 5. led (akku) is dark !!
i replaced the akku , but the alarm no changed
can anybody write to me what is the problem ?
i have no parameters ( if they lost…i think that)
can anybody send the procedure to mend machine and
can anybody send the parameters?

regards, kiss

[Ctdave]

I need service on hitachi Seiki ht23s and ht 25 s can contact me at 860-564 4043 we are located in sterling ct

All,

I have decided after many requests to start doing on-site service locally (in the New England area). I can be contacted via email (PM me with info) and respond very quickly, and if the problems get more intricate, I can offer help by phone. If that doesn't help then I can make the trips. I have been servicing these machines for many years and are familiar with the i80, MX3, LX3, Seicos II & III, Micon II & III, Sigma 16, 18 & 21, Fanuc RC4/RB6 (and many other Fanuc based), J300 and the very fun Lambda 10L/40L controls. I have many parts available as well as software (ladders, EPROM programs, parameters) to help you out in any situation. Contact me anytime; I have helped many many people get their machines up and running both in the US and abroad.

John

[Ctdave]

I need service on ht25s and ht 23s nethier machine will start alsovg45 please contact Dave at sterling precision at 860-564-4043

[L98FIERO]

Does anyone have the parameters required to turn on some of the options on the YASNAC MX3 control? I have a Matsuura MC-510V and have contacted Matsuura who said it's no longer supported and that they would try to get the information from Yaskawa who said the same. I'm out of options as far as getting them from the manufacturer as it's no longer supported and am looking for help keeping the control useful.

[Flyinfool]

Hi John
I have a Hitec-Turn 20SII with a Seicos LIII control. We just had to replace the power supply. the machine was down for 4 months waiting on the new power supply. Now at power up we are getting a "[1009] HI SYSTEM TABLE ERROR" and another screen that just says "SYSTEM TABLE CHECK-SUM ERROR" There is also a battery warning, Could it be that the battery got low enough in the 4 months of down time to corrupt some files but not loose them completely? There was a program loaded in the machine when we shut it down 4 months ago, that program is still there and looks correct.

[shas595]

Just sent you a PM, take a look,
John

Hi John
I have a Hitec-Turn 20SII with a Seicos LIII control. We just had to replace the power supply. the machine was down for 4 months waiting on the new power supply. Now at power up we are getting a "[1009] HI SYSTEM TABLE ERROR" and another screen that just says "SYSTEM TABLE CHECK-SUM ERROR" There is also a battery warning, Could it be that the battery got low enough in the 4 months of down time to corrupt some files but not loose them completely? There was a program loaded in the machine when we shut it down 4 months ago, that program is still there and looks correct.

Sent from my iPhone using Tapatalk