Bump? anyone?
Hi all.
I have a Hitachi Seiki VK45 VMC. Since support is so limited on this machine, I try to take as many precautions as I can. I would like to back up my ladder program. I already have all the paremeters backed up but not the ladder it's self.
I have the WinYumo (win yu yu) software and the correct serial cable plus this document:
https://secure.filesanywhere.com/fs/...8661626fb3b26a
shows how to put the ladder onto the mill. I need to get the ladder OFF so I can save it! Plus I have a friend who has lost his ladder and I would like to send him a copy of mine.
Last thing in the world I want to do is hose mine trying to copy it
I think, the PC side of the thing is fairly common. Here is a picture of my screen in the PC mode:
Well the pic does not show so here is the link for it: https://secure.filesanywhere.com/fs/...6b8661657279a8
it looks like this:
** M16-II Ver5.0 **
F1 SEQUENCE F2 MACHINE F3 MONITOR F4 LADDER F5 ALARM F6 END
I can figure out WinYumo, it's the mill I am worried about. If anyone knows the proceedure to get the mill to send the ladder to WinYumo I would sure love to know how. Also let me know what kinds of "stupd" things to watch out for so I don't hammer my "working" mill !!!!!!!
Thank you
Dan Clemens
Summerville, Oregon
Similar Threads:
I tried it! No luck!
I connected the serial cable to the middle pc board (the one with the write enable switch on it)
I set Win yu yu to 4800 baud, 8 bit, no parity and 2 stop bits. I then pressed "Free RX" it asked for a file name, I typed "my-ladder" pressed "save" Win yu yu said "Receive Data?" I pressed yes.
on the mill, PC screen:
I pressed F1 SEQUENCE -> F5 RS232 -> F4 BAUDRATE (ARROW TO 4800,INPUT KEY) -> F2 WRITE (ARROW TO 128,INPUT) , READ ADDRESS 0000, INPUT, says WRITE START, WRITE ENABLE SWITCH ON!
The mill begins to send the ladder but the "framing error" shows up.
Any one know how to correct this?
Dan Clemens
Summerville, Oregon
Dancy.
could you share files again?
Mike
Anyone have a copy of yuyu etc they like to share?
Thanks
If anyone needs Winyumo (yuyu) here is a link to where I stored it at FilesAnywhere
https://www.filesanywhere.com/fs/v.a...8e5c607477af6e
If you get this to work, PLEASE send me details, as you can see from the above posts, I have not been able to back up my ladder, if I can get it off I will make it available to those of you that have lost yours.
Dan
hello all,
I have been using this software for a while now. Please message me with your specific problem and machine/control and I am sure I can help you out. Also let me know if there are any errors you are getting as well.
John
Dear Sirs,
I have a lathe Hitachi_Seiki_HT20S2 with SEICOS Computer and Micon M16-II ver 5.00 PC Board. I have lost PLC program. If a copy is available, could be much appreciated to send me. My mail is <skiafas@otenet.gr> Thanks
KIAF
Service engineer
Hello,
please check your email. I sent you a message,
John
I did later get this procedure to work....
details here
https://www.filesanywhere.com/fs/v.a...885a61727cb49a
Hi Dancy,
The link does not work, could you load it again, or could write down the steps which worked with you
sting
Hello
I have some problem with my machine.
Model is HC400 Hitachi seiki control fanuc 15MA.
Main board is SEICOS M16-II .
Dear Sirs,
Model is HC400 Hitachi seiki control fanuc 15MA.
I have a lathe Hitachi_Seiki_HC400_FANUC 15MA with SEICOS Micon M16-II ver 7.5** PC Board.
I need Ladder.
My mail is <pcorrect@nate.com>
Thanks
Hello,
Does anyone have a copy of the software for communications with Seico controller on a Hitachi Seiki HC500 with fanuc 11M control?
I have tried the links in this thread - they appear to no long be functional.
Thanks,
Jay Ostrander
Absolute CNC Machinetools, LLC.
Jay
sent you a PM
Hello everyone, I need your help, step by step procedure to back up and installation of all Michon 16
Boy, your right. \
Dead links File share must have done some reorganization or something. Let's try some fresh links:
WinYuMo and params: https://www.filesanywhere.com/fs/v.a...8c616271b8a6af
"how I did it files": https://www.filesanywhere.com/fs/v.a...885a61727cb49a
I think that is all I had posted
Let me know if not working
HI*I have a hitachi seiki vk45 vmc Ladder corrupted*and no backup and no softwarecan you please*help me(austrikengineering@gmail.com)
- - - Updated - - -
HI yoni
*I have a hitachi seiki vk45 vmc Ladder corrupted*and no backup and no softwarecan you please*help me(austrikengineering@gmail.com)
Hi Dan, can you please send me the documents and software?
email: gongkong888@aliyun.com
Appreciation to your help!