Hitachi Seikis

Page 1 of 12 123411 ... LastLast
Threads 1 to 20 of 238

Forum: Hitachi Seikis

Discuss Hitachi Seikis here!

  1. hitachi seiki HTS III , seicos control corrupted

    Started by reymoreno06‎, 07-10-2018 12:34 PM
    seicos
    • Replies: 2
    • Views: 100
    Today, 11:36 AM Go to last post
  2. Unhappy Hitec-Turn 20 Tailstock

    Started by Cobbettm‎, Today 01:28 AM
    hitachi, hitec-turn, ladder logic, seiki, tailstock
    • Replies: 0
    • Views: 56
    Today, 01:28 AM Go to last post
  3. Need Help!- setting z work zero

    Started by positiverake‎, Yesterday 10:01 PM
    cnc, lathe, liii, seicos, tool
    • Replies: 0
    • Views: 74
    Yesterday, 10:01 PM Go to last post
    • Replies: 0
    • Views: 61
    07-10-2018, 01:31 AM Go to last post
  4. Hitachi Seiki Repair / Service / Support

    Started by shas595‎, 06-15-2015 09:31 AM
    5 Pages
    1 2 3 4 5
    • Replies: 51
    • Views: 3,430
    07-10-2018, 12:07 AM Go to last post
    • Replies: 4
    • Views: 297
    06-02-2018, 03:29 AM Go to last post
  5. Need Help!- VS50 Issues after transportation

    Started by caseybarsness‎, 05-23-2018 07:17 PM
    atc, axis, cycle, machine, powering
    • Replies: 2
    • Views: 186
    05-29-2018, 03:30 PM Go to last post
  6. VS50 +X over travel alarm

    Started by WC56‎, 04-09-2018 01:48 AM
    alarm, atc, move, tool, travel
    • Replies: 6
    • Views: 318
    05-23-2018, 07:00 AM Go to last post
  7. Need Help!- What is the SL Bus?

    Started by MWinrich-KMC‎, 05-14-2018 12:50 PM
    bus, error, i/o, machine, slbus
    • Replies: 1
    • Views: 153
    05-14-2018, 02:30 PM Go to last post
  8. Need Help!- Hitachi Seiki VM40 ladder back up

    Started by mnankov‎, 04-30-2018 02:02 AM
    backup, hitachi, ladder, seiki, vm40
    • Replies: 2
    • Views: 242
    05-12-2018, 02:33 AM Go to last post
  9. Run program from computer via RS232 (aka DNC)

    Started by =aike=‎, 04-22-2018 11:21 AM
    cnc, computer, load, program, run
    • Replies: 5
    • Views: 301
    04-24-2018, 02:38 AM Go to last post
    • Replies: 4
    • Views: 420
    04-03-2018, 07:43 PM Go to last post
  10. HiCell 23B - Polar interpolation

    Started by marcin75‎, 04-02-2018 11:16 AM
    • Replies: 0
    • Views: 98
    04-02-2018, 11:16 AM Go to last post
  11. Problem- Control alarms

    Started by BOBTEAM‎, 03-08-2018 03:58 PM
    alarms, batteries, control, disconnected, error
    • Replies: 3
    • Views: 452
    03-13-2018, 12:28 PM Go to last post
  12. Need Help!- VS50 DNC problem

    Started by WC56‎, 03-12-2018 04:26 AM
    cable, dnc, rs232, screen, send
    • Replies: 0
    • Views: 206
    03-12-2018, 04:26 AM Go to last post
  13. Hitachi Seikis VK45 II - Seicos M3 - Error 867

    Started by firstreal‎, 02-20-2018 05:37 AM
    • Replies: 4
    • Views: 569
    03-01-2018, 08:31 AM Go to last post
  14. Need Help!- 5NE-1100

    Started by juanfmoralese‎, 02-13-2018 10:12 PM
    5ne-1100, control, fanuc, lathe, seiki
    • Replies: 0
    • Views: 221
    02-13-2018, 10:12 PM Go to last post
  15. 3NE-300 drawings

    Started by Lary Alvey‎, 02-04-2014 10:40 AM
    3ne
    • Replies: 2
    • Views: 581
    02-02-2018, 06:18 PM Go to last post
  16. Exclamation Problem- Hitachi 23B hicell Seicos LIII not working

    Started by xxx83‎, 12-26-2017 01:06 PM
    • Replies: 11
    • Views: 719
    01-19-2018, 02:06 AM Go to last post
  17. Need Help!- Hitachi Seiki HC400 All Over Travel Alarm

    Started by Billet Carb‎, 01-16-2018 04:21 PM
    hc 400 overtravel alarms, machine, problem, received, voltage
    • Replies: 0
    • Views: 207
    01-16-2018, 04:21 PM Go to last post

Page 1 of 12 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 5 users browsing this forum. (0 members & 5 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands