Hardinge Lathes


Page 1 of 31 123411 ... LastLast
Threads 1 to 20 of 605

Forum: Hardinge Lathes

Discuss Hardinge Lathes here.

  1. Need Help!- Can't home Z 500 over travel alarm

    Started by adamant‎, 04-25-2012 08:23 AM
    • Replies: 6
    • Views: 26,343
    11-27-2019, 12:15 AM Go to last post
  2. Need Help!- 300 APC alarm

    Started by mereboy‎, 01-05-2012 07:30 PM
    everyone
    • Replies: 15
    • Views: 22,329
    10-23-2012, 09:09 PM Go to last post
  3. Need Help!- Hardinge Omniturn Lathe

    Started by K_Labs‎, 05-20-2011 05:27 PM
    4 Pages
    1 2 3 4
    • Replies: 70
    • Views: 15,628
    04-04-2012, 11:27 PM Go to last post
  4. Considering a Hardinge Conquest 42, advice?

    Started by dahui‎, 10-09-2010 12:08 PM
    maybe, sub
    • Replies: 18
    • Views: 15,159
    06-02-2012, 10:13 PM Go to last post
  5. CHNC Turret with PLC...CONVERSION LOG.

    Started by nate‎, 06-06-2011 11:45 AM
    3 Pages
    1 2 3
    • Replies: 56
    • Views: 14,445
    07-25-2011, 01:07 PM Go to last post
    • Replies: 12
    • Views: 10,816
    03-30-2022, 04:17 PM Go to last post
  6. Alarm 1006 on hardinge lathe

    Started by TARIQ08‎, 07-04-2008 08:27 AM
    • Replies: 7
    • Views: 9,526
    09-10-2008, 08:33 AM Go to last post
  7. 1987 CHNC II / Hardinge

    Started by teamjnz‎, 04-10-2009 10:16 PM
    • Replies: 15
    • Views: 8,849
    10-08-2023, 08:59 PM Go to last post
  8. Need Help!- Hardinge CHNC 1 Power up machine home!

    Started by Machineit‎, 08-02-2012 09:00 PM
    2 Pages
    1 2
    • Replies: 28
    • Views: 8,497
    05-04-2015, 09:42 AM Go to last post
  9. Problem- Conquest 42 / Fanuc 0-TC / Parameters needed

    Started by MorueM‎, 08-26-2014 04:48 PM
    air, alarm, backup, brake, cause, conquest, conquest 42, coolant, csgeneral.txt.dat, fanuc, hardinge, indexer, load, load meter, lost, machine, needed, parameters, part catcher, probe, return, said, say, serial, service, since, spindle, sub, then, tools, we’ve, work
    • Replies: 16
    • Views: 7,281
    02-11-2022, 02:14 PM Go to last post
  10. Need Help!- adjusting the turret on Conquest 42

    Started by dango‎, 07-27-2009 01:26 PM
    not
    • Replies: 7
    • Views: 6,654
    11-04-2009, 10:41 PM Go to last post
  11. Need Help!- Hardinge HLV-H lathe manuals needed

    Started by undecided‎, 08-20-2009 10:23 AM
    • Replies: 2
    • Views: 6,220
    10-02-2009, 01:39 AM Go to last post
  12. Hey, finally a section for one of my favorite lathes.

    Started by g-codeguy‎, 05-08-2008 09:27 AM
    2 Pages
    1 2
    maybe, not, took
    • Replies: 25
    • Views: 6,068
    04-20-2018, 09:18 AM Go to last post
  13. Need Help!- Reinstate Collet Close after Parameter Loss

    Started by ::Andy::‎, 03-31-2014 06:11 PM
    except, said, then
    • Replies: 8
    • Views: 6,017
    07-29-2021, 10:22 AM Go to last post
  14. Need Help!- Hardinge Conquest T 42 FANUC 0T optional parameters

    Started by bobancurug‎, 09-17-2011 02:34 PM
    • Replies: 10
    • Views: 5,999
    09-19-2015, 11:17 PM Go to last post
  15. new guy with an accuslide

    Started by nismopu‎, 08-20-2009 11:23 AM
    its, look, next, not, went
    • Replies: 12
    • Views: 5,995
    11-07-2020, 11:50 PM Go to last post
  16. Question work shift

    Started by teamus‎, 04-14-2009 01:31 PM
    2 Pages
    1 2
    sub, subtracted, then
    • Replies: 22
    • Views: 5,749
    06-10-2009, 06:32 AM Go to last post
  17. Need Help!- 3 PHASE CONVERTER

    Started by moonman5‎, 02-12-2017 06:26 AM
    2 Pages
    1 2
    • Replies: 30
    • Views: 5,608
    02-23-2017, 11:18 AM Go to last post
  18. Need Help!- E Torque Limiter Fault, Error 1053

    Started by toolloon‎, 02-02-2012 08:32 PM
    far, not
    • Replies: 5
    • Views: 5,605
    02-23-2012, 11:26 AM Go to last post

Page 1 of 31 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 14 users browsing this forum. (0 members & 14 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands