Hardinge Lathes


Page 1 of 26 123411 ... LastLast
Threads 1 to 20 of 516

Forum: Hardinge Lathes

Discuss Hardinge Lathes here.

  1. HARDINGE CHNC 1 WIRING SCHEMATIC

    Started by moonman5‎, 02-07-2017 06:12 AM
    • Replies: 10
    • Views: 1,388
    05-07-2018, 02:00 PM Go to last post
  2. Problem- Hardinge GN-6 Superslant - Spindle fault

    Started by NEC‎, 11-19-2015 02:48 PM
    • Replies: 7
    • Views: 732
    04-23-2018, 11:15 AM Go to last post
  3. Hey, finally a section for one of my favorite lathes.

    Started by g-codeguy‎, 05-08-2008 09:27 AM
    3 Pages
    1 2 3
    maybe, not, took
    • Replies: 25
    • Views: 4,512
    04-20-2018, 09:18 AM Go to last post
    • Replies: 0
    • Views: 80
    04-19-2018, 10:49 AM Go to last post
    • Replies: 8
    • Views: 219
    04-18-2018, 05:24 PM Go to last post
  4. Can I join the club? I have a T42 too.

    Started by torinwalker‎, 04-17-2018 10:32 PM
    offset, spindle, sub-spindle, t42, working
    • Replies: 0
    • Views: 85
    04-17-2018, 10:32 PM Go to last post
  5. Need Help!- Conquest T42: Opening main collet more than few seconds trips hydraulic motor breaker

    Started by torinwalker‎, 03-14-2018 08:21 PM
    3 Pages
    1 2 3
    • Replies: 33
    • Views: 846
    04-14-2018, 09:21 PM Go to last post
  6. New Machine Build- Stepper Motor verses Ball Screw Relationships

    Started by DDjrouter‎, 04-07-2018 10:59 PM
    ball, diameter, engineering, screw, stepper
    • Replies: 4
    • Views: 168
    04-08-2018, 01:37 PM Go to last post
  7. Build Thread- spindle drive for CHNC-I

    Started by jmelson‎, 04-07-2018 12:20 PM
    drive, fanuc, motor, original, spindle
    • Replies: 6
    • Views: 171
    04-07-2018, 11:46 PM Go to last post
  8. Build Thread- Fanuc OT to DC_CNC conversion.

    Started by Jim Dawson‎, 02-09-2018 12:36 AM
    • Replies: 8
    • Views: 595
    04-07-2018, 01:10 AM Go to last post
  9. Need Help!- Hardinge conquest SP parameters lost!

    Started by justinzwier‎, 04-02-2018 02:30 PM
    conquest, hardinge conquest, made, parameters, parameters needed
    • Replies: 0
    • Views: 97
    04-02-2018, 02:30 PM Go to last post
  10. Need Help!- Post for BobCad software

    Started by Machineit‎, 03-29-2018 06:36 PM
    bobcad, lathe, license, post, software
    • Replies: 3
    • Views: 160
    03-30-2018, 09:19 AM Go to last post
  11. Need Help!- Hardinge HNC with Fanuc 21-T controller will not power display

    Started by timjz‎, 03-03-2018 01:55 PM
    • Replies: 4
    • Views: 334
    03-25-2018, 08:31 AM Go to last post
  12. Need Help!- Can you Identify these Shop-Made Hardinge Tool Holders?

    Started by JohnnyTurn‎, 03-17-2018 02:24 PM
    • Replies: 0
    • Views: 108
    03-17-2018, 02:24 PM Go to last post
  13. Need Help!- Hardinge GS51 Lathe, cutting wrench flats

    Started by Sierra Bullets‎, 03-12-2018 07:45 AM
    cut, flats, lathe, program, spindle
    • Replies: 1
    • Views: 194
    03-12-2018, 12:53 PM Go to last post
  14. Solved deleted

    Started by DOA‎, 03-09-2018 12:27 PM
    cut, cutting, flats, program, spindle
    • Replies: 0
    • Views: 161
    03-09-2018, 12:27 PM Go to last post
  15. New Machine Build- HC CNC Conversion

    Started by EmeraldIsleforg‎, 02-20-2018 01:22 PM
    cnc, hardinge hc, linuxcnc, turret
    • Replies: 4
    • Views: 371
    03-01-2018, 07:29 PM Go to last post
  16. Hardinge T42 - G76 Sub-Spindle Problem

    Started by JohnnyTurn‎, 02-26-2018 04:51 PM
    bad, cycle, g76, thread, work
    • Replies: 0
    • Views: 161
    02-26-2018, 04:51 PM Go to last post
  17. conquest T42 Fanuc 18A

    Started by Willydke‎, 01-14-2018 12:56 PM
    board, imposible, parameter, reload, restablis
    • Replies: 0
    • Views: 364
    01-14-2018, 12:56 PM Go to last post
  18. Need Help!- 1994 Hardinge GT Parameter help

    Started by ::Andy::‎, 12-11-2017 04:59 AM
    alarm, hardinge, machine, reloading, x-axis
    • Replies: 2
    • Views: 318
    12-29-2017, 11:28 AM Go to last post

Page 1 of 26 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 5 users browsing this forum. (0 members & 5 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands